UFS Underfloor piping systems - OBO BETTERMANN

Mounting lid 250-2/3 for GES2, 282x282x4, Strip-galvanised, DIN EN 10147, Steel, St

Mounting lid 250, nominal size 2. Mounting lid for underfloor junction and branch box of type UZD250-3/4 for the installation of an installation unit of nominal size 2. Installation opening 3 mm recessed for later blanking lock with lid blind plate.

Mounting lid 350-2/3 for GES9, 383x383x4, Strip-galvanised, DIN EN 10147, Steel, St

Mounting lid 350, nominal size 9. Mounting lid for underfloor junction and branch box of type UZD350-3/4 for the installation of an installation unit of nominal size 9. Installation opening 3 mm recessed for later blanking lock with lid blanking plate.

Barrier strip for OKA2, Strip-galvanised, DIN EN 10147, Steel, St

OKA2 TW 60 partition wall, for OKA-W channel 2400x15x47 Steel, St, galvanized in band, DIN EN 10346

Separating retainer, trunking height 60 mm. Divider for use in the floor trough of previously prepared OKA-W trunking units.

Service outlet for duct mounting, Iron grey, 7011, Polyamide, PA

Service outlet, round, for screed height 55 mm. GESR9 service outlet with a fixed construction height of 55 mm for indoor use. With two fitted plug housings for vertical mounting of Modul 45 devices and four strain reliefs. Two installation frames are required to mount Modul 45 devices.The data modules are mounted using an optional mounting plate MPMT45. The service outlet is equipped with universal fastening brackets.

Service outlet for universal mounting, Stainless steel, grade 304, VA, 1.4301

GES6M-2 service outlet with handle clamp. Service outlet with handle clamp for up to 9 individual Modul 45 devices in 3 UT3 universal supports, use in trunking systems and system floors for indoor use.Locking ladder made of galvanised sheet steel. The floor covering thickness is set to 5 mm, adjustable to 10 mm if necessary. Service outlet with handle clamp, 3-compartment, for the installation of MT6 mounting support. Three type APMT2 cover plates can be installed.

Junction box insert for universal mounting, Iron grey, 7011, Polyamide, PA

ZES9 inspection cover. Junction box insert for blank closing of a square mounting opening of nominal size 9 in trunking systems and in raised and cavity floors for indoor use. Polyamide floor covering profile.Recess is 5 mm, if necessary, adjustable to 3, 8 or 10 mm.

Junction box insert for universal mounting, Iron grey, 7011, Polyamide, PA

ZES6 inspection cover. Junction box insert for blank closing of a rectangular mounting opening of nominal size 6 in an underfloor duct or trunking system or in raised floor for indoor use. Polyamide floor covering profile.Recess is 5 mm, if necessary, adjustable to 3, 8 or 10 mm.

Installation frame for 4 x 1 Modul 45, Graphite black, 9011, Polyamide, PA

Installation frame for four single Modul 45® devices. For the installation of 4 individual Modul 45 devices for System 55 service outlets with mounting support for vertical installation of Modul 45 devices.The installation frame is designed for use with 0° sockets (normal installation position, contact openings on right and left) and their use in conjunction with straight connectors (not angled connectors).

Underfloor box empty for GES9/55UV, 367x367x55, Strip-galvanised, DIN EN 10147, Steel, St

UGD250-3 underfloor box for GES9/55. Underfloor accessory box with mounting lid and lid blanking plate with sheet steel side walls. For the installation of a square GES9 55 service outlet in screed heights of 55 mm or more. Height can be infinitely adjusted to the nominal screed height and the screed can be worked flush to the screed scraping edge. With 7 x M20, 3 x M25, 4 x M32 pipe insertion openings on each side. Usable pipe size at a system height of 55 mm: M20.

End cover for OKA-G and OKA-W, Strip-galvanised, DIN EN 10147, Steel, St

Trunking end piece, height 40−150 mm. Ready-to-mount trunking end piece, consisting of a flexible apron with side and floor covering guide profiles. The scope of delivery contains trunking connection brackets and a height-adjustable fixing bracket.

End cover for OKA-G and OKA-W, Strip-galvanised, DIN EN 10147, Steel, St

Trunking end piece, height 40−150 mm. Ready-to-mount trunking end piece, consisting of a flexible apron with side and floor covering guide profiles. The scope of delivery contains trunking connection brackets and a height-adjustable fixing bracket.

Flushfloor trunking unit blank, 2400x200x40, Strip-galvanised, DIN EN 10147, Steel, St

OKA-W2004030 pavement flush channel, blind 2400x200x40 Steel, St, strip galvanized, DIN EN 10346

Trunking unit, blank, height 40−70 mm. Ready-to-mount trunking unit with three blanking lids for cable laying, consisting of the trunking base (floor trough with side and floor covering contact profiles) and trunking lid. Floor trough with holding straps for self-contacting mounting of separating retainers. The scope of delivery contains 6 height-adjustable fixing brackets, 6 screed anchors and lid butt seals (3x for nominal trunking widths of 200 and 300) or height-adjustable lid butt supports: 3x for nominal trunking width 400 and 6x for nominal trunking widths 500 and 600. Trunking lid screwed on for delivery.

Flushfloor trunking unit blank, 2400x200x60, Strip-galvanised, DIN EN 10147, Steel, St

OKA-W2006050 pavement flush channel, blind 2400x200x60 Steel, St, strip galvanized, DIN EN 10346

Trunking unit, blank, height 60−110 mm. Ready-to-mount trunking unit with three blanking lids for cable laying, consisting of the trunking base (floor trough with side and floor covering contact profiles) and trunking lid. Floor trough with holding straps for self-contacting mounting of separating retainers. The scope of delivery contains 6 height-adjustable fixing brackets, 6 screed anchors and lid butt seals (3x for nominal trunking widths of 200 and 300) or height-adjustable lid butt supports: 3x for nominal trunking width 400 and 6x for nominal trunking widths 500 and 600. Trunking lid screwed on for delivery.

Flushfloor trunking unit blank, 2400x400x60, Strip-galvanised, DIN EN 10147, Steel, St

OKA-W4006050 flush pavement channel, blind 2400x400x60 Steel, St, strip galvanized, DIN EN 10346

Trunking unit, blank, height 60−110 mm. Ready-to-mount trunking unit with three blanking lids for cable laying, consisting of the trunking base (floor trough with side and floor covering contact profiles) and trunking lid. Floor trough with holding straps for self-contacting mounting of separating retainers. The scope of delivery contains 6 height-adjustable fixing brackets, 6 screed anchors and lid butt seals (3x for nominal trunking widths of 200 and 300) or height-adjustable lid butt supports: 3x for nominal trunking width 400 and 6x for nominal trunking widths 500 and 600. Trunking lid screwed on for delivery.

Service outlet, complete with protective contact socket, Stainless steel, grade 304, VA, 1.4301

UDHOME4 floor box, with universal support UT3 45 3, triple VDE, stainless steel. Square floor box for use in dry-cleaned cavity and screed floors in indoor areas. Installation housing with pre-marked insertion openings for pipes (M25). With two UT3 45 3 universal supports and a triple protective contact socket. Cover adjustable to top edge of floor covering using four height-adjustment supports. The minimum installation depth is 95 mm, the height-adjustment range + 30 mm.Surfaces made of stainless steel and visible in the floor covering.

Flush mounted housing for GES4-2, galvanized band, DIN EN 10147, Steel, St

Underfloor box for GES4. Square installation housing for one GES4-2 service unit for outlet in screed floors for indoor use. With pre-marked insertion openings for pipelines (M25) on all four sides. In the as-delivered state, the installation housing is closed with a mounting protection lid. The minimum installation depth is 70 mm, the height-adjustment range +30 mm.

Set portamec., Mount canal, gray iron, 7011, Polyamide, PA

Mec holder set. GES2 KU 7011, for recessed Polyamide, PA,

GES2 with MT3 45. Mechanism unit with all the system accessories required for floor mounting. The scope of delivery includes a nominal size 2 mechanism holder with universal clamping angle and a modular holder for 3 Modul 45 mechanisms. Mechanism holder unit with carpet protective frames, hinged lid and polyamide-based cable outlet, in RAL 7011 colour. The hinged lid has a recess to place a final end of pavement of 5 mm.

Set portamec., For universal mounting, gray iron, 7011, Polyamide, PA

GES6-2 with UT3 45. Service outlet with all necessary system accessories for direct installation in screed floors in interior areas.The scope of delivery contains a service outlet of nominal size 6 with universal fastening bracket and three universal supports, each for three Modul 45® devices. Service outlet with carpet protection frame, hinged lid and cord outlet made of polyamide in the colour RAL 7011. 10 mm floor covering recess in the hinged lid (changeable to 3, 5 or 8 mm).

Complete kit for all types of floors, stainless steel 1.4301, VA, 1.4301

Complete kit RKSN2 4 KU V25 for all types of floors Stainless steel 1.4301, A2, 1.4301

RKSN2 4 with UT3 45. Cap and frame set with adjustable height with all the necessary system accessories for direct mounting on all types of floors that need dry cleaning indoors. The scope of delivery includes:- Box of nominal size 4 with cable output,- Two universal UT3/45 brackets for three Modul 45® mechanisms each. Stainless steel cable box and outlet. Pavement recess in the box: 25 mm.

BUCKET P/MECAN 3 MODUL45 UT3 45 3

UT3 universal support, with cover plate for Modul 45® devices, system length 165 mm. Universal support with two strain reliefs, mounting bridges, partition and cover plate UT3 P3 for the installation of 3 Modul 45 devices in device installation units of the nominal sizes 2, R4, 4 and R7.

PLATE 2XRJ45 GESR2 TIP.C MP R2 2C

Mounting plate for data technology, type C. Mounting plate to accept two data connection modules of the following types: Brand-Rex: shielded; EKU: E-Stone; Dätwyler: KS-T, MS-K and KU-T module; R&M: Snap-In and Keystone; Rutenbeck: UM and UMflex; SETEC: MKJ, UKJ and XKJ; Siemon TERA; Telegärtner: AMJ and UMJ.Dimensions of a mounting opening in mm: 19.30 x 14.80.

UNIT P/MECAN GES R2 7011

Service outlet with hinged cover and cord outlet, GES R2. Service outlet with hinged cover and cord outlet for GES R2 floor socket for direct installation in the MT R2 installation socket.For use in dry-cleaned floors for indoor use.

UNIT P/MECAN T. ABAT GES R2 Or

GES R2 Ni floor socket, with flip-top lid Die-cast with zinc, Zn, nickel-plated

Flip-top with sliding slide, nickel. Mechanism holder set with hinged lid and sliding sliding for GES R2 floor socket for direct mounting in the MT R2 installation box in indoor areas. When closed, the entire unit can be cleaned with water.

COVER ASSEMBLY DUG 350-3 4

Mounting cover 350, nominal size 4. Mounting lid for underfloor junction and branch box of type UZD350-3 and UZD350-4 for the installation or creation of an installation unit. Installation opening 3 mm recessed as a later blanking lock with lid blind plate.

BOX PAVEMENT GES R2 UD GES R2

Screed box for GES R2. Height-adjustable screed box for the installation of the installation socket of the GES R2 floor socket.With 2x2 insertion openings for installation pipes (M20/M25).

BUCKET GESR2 P/2XVDE MT R2 VDE

Installation socket, double, VDE. Installation socket for GES R2 floor socket for mounting in UD GES R2 screed box and in raised floor plates.

CAP AND MARCO SQ RKSN2 4 VS 20

Height-adjustable cassette with cord outlet, RKSN, stainless steel. Height-adjustable cassette of nominal size 4 with cord outlet for installation of accessories in dry-cleaned floors for indoor use.Height-adjustable cassette for cord outlet, 2-compartment. 2 APMT2 cover plates can be installed. For the installation of 2 UT3 universal supports for 4 individual installation devices with support ring/support clamp or 6 Modul 45 devices.

MOUNTING COVER DUG 250-3 6

Mounting lid 250, nominal size 6. Mounting lid for underfloor junction and branch box of type UZD250-3/4 for the installation of an installation unit of nominal size 6. Installation opening 3 mm recessed for later blanking lock with lid blind plate.

BLIND-OFF CAP DU 350-2

Blanking lid for UZD350. Blanking lid for frameless end cover of the underfloor junction and branch boxes of type UZD350.

SET PORTAMECANISMOS GES6-2U10T 7011

GES6 service outlet with locking slider. Service outlet with locking slider for up to 9 individual Modul 45 devices in 3 UT3 universal supports, use in trunking systems and system floors for indoor use.Floor covering recess in the hinged cover pre-adjusted to 5 mm, if necessary adjustable to 3, 8 or 10 mm.Service outlet with locking slider, 3-compartment, for the installation of MT6 mounting support. Three type APMT2 cover plates can be installed.Floor covering recess in the hinged cover pre-adjusted to 5 mm, if necessary adjustable to 3, 8 or 10 mm.

SET P. CLEANING WITH WATER GRAF9-2 U 7011

GRAF9 universal service outlet, wet-cleaned with structured lid. Service outlet with tube body for wet-cleaned floors for up to 12 individual Modul 45 devices in 3 UT4 universal supports, use in duct and trunking systems and system floors indoors.Service outlet with tube body for wet cleaned floors, 3-compartment, for the installation of MT9 mounting support. Three type APMT5 cover plates can be installed.

SET COVER AND FRAME ROUND RKS2 R4 V25

RKS2 R4 V25 round cover and frame set, with cable outlet Ø215mm Stainless steel 1.4301, A2, 1.4301,

Height-adjustable cassette with cord outlet, RKSR, stainless steel. Height-adjustable cassette of nominal size R4 with cord outlet for installation of accessories in dry-care floors for indoor use.Height-adjustable cassette for cord outlet, 2-compartment. 2 APMT2 cover plates can be installed. For the installation of 2 UT3 universal supports for 4 individual installation devices with support ring/support clamp or 6 Modul 45 devices.

UNIT PORTAMEC. FULL UDHOME4 2V MT U

Portamec unit. complete UDHOME4 2V UT U, with MT trays, without schukos Stainless steel 1.4301, A2, 1.4301,

UDHOME4 2V MT U 7427248 UDHOME4 floor box, with MT3 module support, freely equippable, stainless steel

UDHOME2 floor socket, with cord outlet, with floor covering recess, 2x VDE, stainless steel. Square floor socket for use in dry-care cavity and screed floors in indoor areas. Installation housing with pre-marked insertion openings for pipes (M20/M25). Cover adjustable to top edge of floor covering using four height-adjustment supports. The minimum installation depth is 110 mm, the height-adjustment range 25 mm.Frame and cover made of stainless steel and visible in the floor covering. With 2 Modul 45® sockets in the mounting support and an optional data technology support for up to 2 data connection modules.

Floor socket with lid Nickel 2xtomas VDE and box 140x140x85 Die casting with zinc, Zn

GES R2 as an assembly kit. Round GES R2 service outlet with hinged cover, floor covering protection frame and UD GES R2 screed socket for installation in floors with screed structures in internal areas. Installation unit with a double power socket with a 33° insertion direction. At the side, next to the socket, there is space for an optional two connection sockets for data technology applications. When closed, the installation unit can be wet-cleaned. The minimum installation depth is 85 mm. Surface: Nickel-plated.

Empty full unit 140x140x110, stainless steel, A2

UDHOME2 floor socket with notch for floor covering, unsealed, stainless steel

Empty full unit 140x140x110, stainless steel, A2

UDHOME2 floor socket, with cord outlet, without floor covering recess, unequipped, stainless steel. Square floor socket for use in dry-care cavity and screed floors in indoor areas. Installation housing with pre-marked insertion openings for pipes (M20/M25). Cover adjustable to top edge of floor covering using four height-adjustment supports. The minimum installation depth is 100 mm, the height-adjustment range 35 mm.Frame and cover made of stainless steel and visible in the floor covering. Empty housing for up to 2 Modul 45® devices in the mounting support and 2 data sockets in the optional data technology support.

Complete unit UDHOME-ONE GV15, unequipped, with 15 mm BBA 140x140x75 Stainless steel, A2

Complete unit without equipping, with 15 mm BBA UDHOME-ONE GV15

UDHOME-ONE floor socket, with floor covering recess, freely equippable, stainless steel. Square floor socket for use in dry-care systems and screed floors in indoor areas. Installation housing with pre-marked insertion openings for pipes (M20/M25). Cover adjustable to top edge of floor covering using four height-adjustment supports. The minimum installation depth is 75 mm, the height-adjustment range + 30 mm. Frame and cover made of stainless steel and visible in the floor covering. Cover with floor covering recess. Empty housing for one Modul 45® installation device and one data socket. When delivered, the item is closed with a blanking plate.When installing a double protective contact socket/NF socket through a mounting support, the use of an angular connector is only possible at an in

UDHOME-ONE MT UH1 2M45 mounting tray, 2x Modul 45 cut out 45x52x115 Stainless steel, A2

Mounting tray UDHOME-ONE 2x Modul 45 trimmed MT UH1 2M45

UDHOME-ONE mounting support for 2 Modul 45® installation devices. Mounting support to accept up to 2 Modul 45® installation devices. Dimensions of the mounting opening: 37 x 85 mm.When used with a protective contact socket/NF socket in the UDHOME-ONE with floor covering recess, an angular connector can only be used with an installation height of at least 90 mm. Use straight connectors for lower installation heights.

GES R2 KP floor socket, with 140 mm hinged lid Zinc die-casting, Zn coated with electrostatic paint

Floor socket with folding lid GES R2 KP

Service outlet with hinged cover and locking slider, GES R2, deep black. Service outlet with hinged cover and locking slider for GES R2 floor socket for direct installation in the MT R2 installation socket.When closed, the floor socket can be wet-cleaned.

Underfloor channel 2-parts S2 19028-2, 2 compartments 2000x190x28 Steel, St galvanized in band, DIN EN 10346. Unit price and packaging units in meters.

2-part S2 19028-2.2 compartment underfloor channel 2000x190x28 Steel, St, strip galvanized, DIN EN 10346

Underfloor duct, 2 pieces, 2-compartment, duct height 28 mm. Underfloor duct (2 piece) for routing cables in screed-covered underfloor systems, according to EN 50085-2-2. Removable and continuously lockable trunking cover. With separating retainers in the trunking base. Maximum load-bearing capacity to 1.5 kN.

2-part S2 25028-2 underfloor channel, 2 compartments 2000x250x28 Steel, St galvanized in band, DIN EN 10346. Unit price and packaging units in meters.

Underfloor channel 2-parts S2 25028-2.2 compartments 2000x250x28 Steel, St, galvanized in band, DIN EN 10346

Underfloor duct, 2 pieces, 2-compartment, duct height 28 mm. Underfloor duct (2 piece) for routing cables in screed-covered underfloor systems, according to EN 50085-2-2. Removable and continuously lockable trunking cover. With separating retainers in the trunking base. Maximum load-bearing capacity to 1.5 kN.

2-part S3 35028-2 underfloor channel, 3 compartments 2000x350x28 Steel, St galvanized band, DIN EN 10346. Unit price and packaging units in meters.

Underfloor channel 2-parts S3 35028-2.3 compartments 2000x350x28 Steel, St, galvanized in band, DIN EN 10346

Underfloor duct, 2 pieces, 3-compartment, duct height 28 mm. Underfloor duct (2 piece) for routing cables in screed-covered underfloor systems, according to EN 50085-2-2. Removable and continuously lockable trunking cover. With separating retainers in the trunking base. Maximum load-bearing capacity to 1.5 kN.

2-part S3 35048-2 underfloor channel, 3 compartments 2000x350x48 Steel, St galvanized band, DIN EN 10346. Unit price and packaging units in meters.

2-part S3 35048-2.3 compartment underfloor channel 2000x350x48 Steel, St, strip galvanized, DIN EN 10346

Underfloor duct, 2 pieces, 3-compartment, duct height 48 mm. Underfloor trunking (2 piece) for routing cables in screed-covered underfloor systems, according to EN 50085-2-2. Removable and continuously lockable trunking cover. With separating retainers in the trunking base. Maximum load-bearing capacity to 1.5 kN.

VL 250-2 connection, conduction for EÜK-2 323x75x28.2 Steel, St galvanized strip, DIN EN 10346

VL 250-2 Union, conduction for EÜK-2 323x75x28.2 Steel, St, strip galvanized, DIN EN 10346

Connection shackle, conductive, for EÜK-2. Connection shackle for mounting screed-covered underfloor installation ducts. The connection shackle snaps in to the duct sidewalls.

Box for conj.portamec. UGE 2C, for GES2 240x150x88 Steel, St galvanized strip, DIN EN 10346

Box for conj.portamec. UGE 2C, for GES2 240x150x88 Steel, St, strip galvanized, DIN EN 10346

Underfloor box UGE2 for installation pipe and metal duct. Underfloor outlet box with fixed, unchangeable 106 x 182 mm installation opening for an installation unit of nominal size 2. The mounting opening is created using the screed protection cover contained in the scope of supply. The underfloor box has two openings for M20 conduit on the narrow sides. The underfloor box is suitable for screed floor constructions with height 70 mm up to 90 mm.

Derivation box. and reg. UZD350-4 for screeds 80-160mm 500x480x80 Steel, St strip galvanized, DIN EN 10346

Underfloor channel 2-parts S2 19048-2, 2 compartments 2000x190x48 Steel, St galvanized in band, DIN EN 10346. Unit price and packaging units in meters.

Underfloor channel 2-parts S2 19048-2.2 compartments 2000x190x48 Steel, St, strip galvanized, DIN EN 10346

Underfloor duct, 2 pieces, 2-compartment, duct height 48 mm. Underfloor trunking (2 piece) for routing cables in screed-covered underfloor systems, according to EN 50085-2-2. Removable and continuously lockable trunking cover. With separating retainers in the trunking base. Maximum load-bearing capacity to 1.5 kN.

2-part S3 25048-2 underfloor channel, 3 compartments 2000x250x48 Steel, St galvanized band, DIN EN 10346. Unit price and packaging units in meters.

Underfloor channel 2-parts S3 25048-2.3 compartments 2000x250x48 Steel, St, strip galvanized, DIN EN 10346

Underfloor duct, 2 pieces, 3-compartment, duct height 48 mm. Underfloor trunking (2 piece) for routing cables in screed-covered underfloor systems, according to EN 50085-2-2. Removable and continuously lockable trunking cover. With separating retainers in the trunking base. Maximum load-bearing capacity to 1.5 kN.

Mounting lid 250-2/3 for R4, 282x282x4, Strip-galvanised, DIN EN 10147, Steel, St

Mounting lid 250 for installation units of nominal size R4. Mounting lid for underfloor junction and branch boxes of type UZD350-3/4 for the installation of an installation unit of nominal size R4. Installation opening 3 mm recessed as a later blanking lock with lid blind plate.