No products
Product successfully added to your shopping cart
View larger
HC-MOT-TML-SET 1409066 PHOENIX CONTACT Housing set
HC-MOT-TML-SET
1409066
PHOENIX_CONTACT
Housing set
Plug connector. motor for connection drive. Triphasic. Metal housing for electromag compatibility. of taps incl. push-in contact insert, with screw connections (power and control circuit). With blind plugs in the connection. by control duct screw. 4-pole control circuit. With a triangular star bridge. With protective lid. IP54.
Motor connector for three-phase drive, metal housing with EMC sleeves incl. push-in contact insert, with screw connections (power and control circuit). With filler plugs in the control cable screw connection, 4-pos. control circuit, with star-delta bridge, with IP54 protective cover.
Connectors > Housing for rectangular connectors
Field Device Connectors (FDC)
Brand new product in its original packaging covered by the warranties and certifications provided by PHOENIX_CONTACT
Best sellers
▲More info
▲| Safety note | |
| Safety note | WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. |
| • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. | |
| • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. | |
| • The products are suitable for applications in plant, controller, and electrical device engineering. | |
| • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. | |
| • Assembled products may not be manipulated or improperly opened. | |
| • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). | |
| • When using the product in direct connection with third-party manufacturers, the user is responsible. | |
| • For operating voltages > 50 V AC, conductive connector housings must be grounded | |
| • Ensure that the protective or functional ground has been properly connected. | |
| • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector | |
| • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product | |
| • Only use tools recommended by Phoenix Contact | |
| • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. | |
| • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products | |
| • Operate the connector only when it is fully plugged in. | |
| • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. | |
| • Observe the minimum bending radius of the cable. Lay the cable without twisting it. | |
| • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). | |
| Product type | Housing with locking latch |
| Housing type | Sleeve housing |
| Product family | VARIOCON |
| Application | Standard |
| Type | MOT |
| No. of cable outlets | 2 |
| Cable outlet | straight |
| Insulation characteristics | |
| Degree of pollution | 3 |
| Dimensional drawing |  |
| Width | 70.3 mm |
| Height | 131.8 mm |
| Length | 31.5 mm |
| Color of the housing part | gray |
| Flammability rating according to UL 94 | V0 |
| Insulating material group | I |
| Seal material | EPDM |
| Material, insert | FPM |
| Housing material | PA |
| Cable seal material | FKM |
| Contact material | CuZn |
| Contact surface material | Au |
| Contact carrier material | PA |
| Material of contact surface, control contact | Au |
| O-ring material | FKM |
| Locking latch material | Stainless steel |
| Material for screw connection | CuZn |
| Mechanical data | |
| Insertion/withdrawal cycles | ≥ 100 |
| External cable diameter Cable 1 | 7 mm ... 14.5 mm (Unshielded cable) |
| Stripping length of the individual wire | 12 mm (Push-in Technology) |
| External cable diameter | 7 mm ... 14.5 mm (Unshielded cable) |
| Ambient conditions | |
| Degree of protection | IP67 |
| IP67 | |
| Ambient temperature (operation) | -30 °C ... 100 °C |
Datasheet - PDF
▲| Title: | Size: | Type: |
|---|---|---|
| PDF CATALOG PHOENIX CONNECTORS EN.pdf | 68 Mbytes |
|
| PHOENIX CONTACT-1409066-HC-MOT-TML-SET | 134 Kbytes |
|
Reviews (0) ▲
No customer reviews for the moment.
| Rating: |
|
| Name: | |
| Email: | |
| Subject: | |
| Text: | |
| Do you recommend this product to buy? | |
|
|
|
| Add review | |
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.