Product successfully added to your shopping cart
MINI MCR-2-UI-UI
2902037
PHOENIX_CONTACT
1
3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. Screw connection technology, standard configuration.
INTERFACE Components (IF)
* Brand new product in its original packaging covered by the warranties and certifications provided by PHOENIX_CONTACT
Thank you for your interest in our products; we hope the delivery time indicated is to your convenience.
While the order is being processed you can select the type of shipment that best suits your needs: 24-hour air express, standard 48-72 hour land, etc.
The 3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover can be configured using DIP switches and is used for the electrical isolation, conversion, amplification, and filtering of unipolar and bipolar standard and normalized signals. On the input side, the standard analog signals 0 ... 20 mA, 4 ... 20 mA, 0 ... 10 V, 0 ... 5 V, 1 ... 5 V or -10 ... 10 V, and signals2 ... 10 V, 0 ... 20 V, 4 ... 20 V, 0 ... 24 V, 0 ... 30 V, -5 ... 5 V, -20 ... 20 V, -24 ... 24 V, -30 ... 30 V and -20 ... 20 mA are available. On the output side, 0 ... 20 mA, 4 ... 20 mA, 0 ... 10 V, 0 ... 5 V, 1 ... 5 V, -10 ... 10 V and -5 ... 5 V are possible. There is no need for adjustment following a measuring range changeover. The measuring transducer supports fault monitoring and NFC communication.
Width | 6.2 mm |
---|---|
Height | 110.5 mm |
Depth | 120.5 mm |
Ambient temperature (operation) | -40 °C ... 70 °C |
---|---|
Ambient temperature (storage/transport) | -40 °C ... 85 °C |
Degree of protection | IP20 |
Number of inputs | 1 |
---|---|
Configurable/programmable | Yes |
Voltage input signal | 0 V ... 5 V (via DIP switch) |
1 V ... 5 V (via DIP switch) | |
-5 V ... 5 V (via DIP switch) | |
0 V ... 10 V (via DIP switch) | |
2 V ... 10 V (via DIP switch) | |
-10 V ... 10 V (via DIP switch) | |
0 V ... 20 V (via DIP switch) | |
4 V ... 20 V (via DIP switch) | |
-20 V ... 20 V (via DIP switch) | |
0 V ... 24 V (via DIP switch) | |
4.8 V ... 24 V (via DIP switch) | |
-24 V ... 24 V (via DIP switch) | |
0 V ... 30 V (via DIP switch) | |
6 V ... 30 V (via DIP switch) | |
-30 V ... 30 V (via DIP switch) | |
Current input signal | 0 mA ... 20 mA (via DIP switch) |
4 mA ... 20 mA (via DIP switch) | |
-20 mA ... 20 mA (via DIP switch) | |
Max. input voltage | 33 V |
Max. input current | 24 mA |
Input resistance of voltage input | > 1000 kΩ |
Input resistance current input | approx. 63 Ω |
Number of outputs | 1 |
---|---|
Configurable/programmable | Yes |
Voltage output signal | 0 V ... 5 V (via DIP switch) |
1 V ... 5 V (via DIP switch) | |
-5 V ... 5 V (via DIP switch) | |
0 V ... 10 V (via DIP switch) | |
2 V ... 10 V (via DIP switch) | |
-10 V ... 10 V (via DIP switch) | |
Current output signal | 0 mA ... 20 mA (via DIP switch) |
4 mA ... 20 mA (via DIP switch) | |
Max. output current | 22 mA |
Short-circuit current | < 32 mA |
Load/output load voltage output | ≥ 10 kΩ |
Load/output load current output | ≤ 600 Ω (at 20 mA) |
Nominal supply voltage | 24 V DC |
---|---|
Supply voltage range | 9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715)) |
Typical current consumption | 25 mA (Current output, at 24 V DC incl. load) |
54 mA (Current output, at 12 V DC incl. load) | |
Power consumption | ≤ 800 mW (at IOUT= 20 mA, 9.6 V DC, 600 Ω load) |
Connection method | Screw connection |
---|---|
Single conductor/terminal point, solid, with ferrule, min. | 0.2 mm² |
Single conductor/terminal point, solid, with ferrule, max. | 1.5 mm² |
Single conductor/terminal point, solid, without ferrule, min. | 0.2 mm² |
Single conductor/terminal point, solid, without ferrule, max. | 2.5 mm² |
Conductor cross section flexible min. | 0.2 mm² |
Conductor cross section flexible max. | 1.5 mm² |
Min. AWG conductor cross section, flexible | 24 |
Max. AWG conductor cross section, flexible | 12 |
Stripping length | 10 mm |
Screw thread | M3 |
No. of channels | 1 |
---|---|
Maximum transmission error | ≤ 0.1 % (of final value) |
≤ 0.15 % (of final value, at IN: 4 ... 20 mA / OUT: -10 V ... 10 V) | |
Maximum temperature coefficient | 0.01 %/K |
Limit frequency (3 dB) | 30 Hz (via DIP switch) |
5 kHz (via DIP switch) | |
Step response (10-90%) | < 8.5 ms (with 30 Hz filter) |
Protective circuit | Transient protection |
Electrical isolation | Reinforced insulation in accordance with IEC 61010-1 |
Overvoltage category | II |
Pollution degree | 2 |
Rated insulation voltage | 300 V (effective) |
Test voltage, input/output/supply | 3 kV (50 Hz, 1 min.) |
Electromagnetic compatibility | Conformance with EMC Directive 2004/108/EC |
Noise emission | EN 61000-6-4 |
Noise immunity | EN 61000-6-2 When being exposed to interference, there may be minimal deviations. |
Color | gray |
Housing material | PBT |
Mounting position | any |
Assembly instructions | The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715. |
Conformance | CE-compliant |
ATEX | Ex II 3 G Ex nA IIC T4 Gc X |
UL, USA / Canada | UL 508 Listed |
Class I, Div. 2, Groups A, B, C, D T6 | |
Class I, Zone 2, Group IIC T6 | |
Certificate of classification | DNV GL 14445-15HH |
Designation | Electromagnetic RF field |
---|---|
Standards/regulations | EN 61000-4-3 |
Designation | Fast transients (burst) |
Standards/regulations | EN 61000-4-4 |
Designation | Conducted interferences |
Standards/regulations | EN 61000-4-6 |
Title: | Size: | Type: |
---|---|---|
PDF CATALOG PHOENIX INTERFACE TECHNOLOGY AND SWITCHING DEVICES EN.pdf | 27 Mbytes | |
PHOENIX CONTACT-2902037-MINI MCR-2-UI-UI | 137 Kbytes |
No customer reviews for the moment.
Rating: | |
Name: | |
Email: | |
Subject: | |
Text: | |
Do you recommend this product to buy? | |
Add review |
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.