Product successfully added to your shopping cart
SB-8ESSD8AWT00SX
1244966
PHOENIX_CONTACT
1
M40, Conect. plug. for apar. Wall of the Tower.
M40, Device connector front mounting, series: SB, straight, shielded: yes, for standard and SPEEDCON interlock, No. of pos.: 8+4+PE, Direction of rotation: Standard, contact connection type: Socket, Crimp connection, Axial O-ring, 4x Ø4,2, flange dimensions: 40 mm x 40 mm, coding: Signal, coding 2, Item is lead-free in accordance with RoHS II without Exemption 6c (Pb <0.1%)
Home > PHOENIX CONTACT
* Brand new product in its original packaging covered by the warranties and certifications provided by PHOENIX_CONTACT
Thank you for your interest in our products; we hope the delivery time indicated is to your convenience.
While the order is being processed you can select the type of shipment that best suits your needs: 24-hour air express, standard 48-72 hour land, etc.
General | Crimp contacts, 8 x Ø 1 mm, 5 x Ø 3.6 mm, order separately |
Safety note | |
Safety note | WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. |
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. | |
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. | |
• The products are suitable for applications in plant, controller, and electrical device engineering. | |
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences. | |
• Assembled products may not be manipulated or improperly opened. | |
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). | |
• When using the product in direct connection with third-party manufacturers, the user is responsible. | |
• For operating voltages > 50 V AC, conductive connector housings must be grounded | |
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector | |
• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product | |
• Only use tools recommended by Phoenix Contact | |
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. | |
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products | |
• Operate the connector only when it is fully plugged in and interlocked. | |
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. | |
• Observe the minimum bending radius of the cable. Lay the cable without twisting it. | |
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). |
Product type | Circular connectors (device side) |
Connection 1 | |
Head design | Socket |
Insulating body | |
Protection against electric shock | IEC 61984 |
Coding | Signal, coding 2 |
Connection method | Crimp connection |
Contact switching type | Socket |
Application | Hybrid |
Number of positions | 13 |
Direction of rotation | Standard |
Connection profile | 8+4+PE |
Contact diameterPower contacts | 3.6 mm |
Litz wire cross-sectionPower contactsmin. | 1 mm² |
Litz wire cross-sectionPower contactsmax. | 16 mm² |
Rated currentPower contacts | 70 A |
Note | for max. connection cross section |
Rated voltage | 630 V AC |
Rated surge voltage | 6 kV |
Overvoltage category | III |
Degree of pollution | 3 |
Rated voltage (II/3) power contact | 850 V DC |
Rated voltage (III/3) power contact | 630 V AC |
Contact diameterSignal contacts | 1 mm |
Litz wire cross-sectionSignal contactsmin. | 0.06 mm² |
Litz wire cross-sectionSignal contactsmax. | 1.5 mm² |
Nominal current per signal contact | 8 A |
Note | for max. connection cross section |
Rated surge voltage | 6 kV |
Rated voltage (III/3) signal contact | 500 V |
Contact diameter Data contacts | 1 mm |
Litz wire cross-section Data contacts min. | 0.06 mm² |
Litz wire cross-section Data contacts max. | 1.5 mm² |
Rated current per data contact at 25°C | 8 A |
Note | for max. connection cross section |
Rated voltage Data contacts | 50 V |
Rated surge voltage | 1.5 kV |
Installation height | 2000 m |
Housing | |
Housing material | Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn) |
Flange dimensions | 40 mm x 40 mm |
Type of locking | for standard and SPEEDCON interlock |
Pg screw connection | none |
Degree of protection (plugged in) | IP68/IP69K |
Thread type | M40 |
Ambient conditions | |
Ambient temperature (operation) | -40 °C ... 115 °C (see derating curve) |
No customer reviews for the moment.
Rating: | |
Name: | |
Email: | |
Subject: | |
Text: | |
Do you recommend this product to buy? | |
Add review |
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.