No products
Product successfully added to your shopping cart
View larger
ELR 5030-2 IP PN 2701008 PHOENIX CONTACT Electronic motor starter, electronics module without lower part of ..
ELR 5030-2 IP PN
2701008
PHOENIX_CONTACT
Electronic motor starter, electronics module without lower part of housing, 2-channel reversing starter
Automation Software (AS)
* Brand new product in its original packaging covered by the warranties and certifications provided by PHOENIX_CONTACT
More info
▲Product description
The PROFINET motor starters are designed as distributed motor starters with IP67 protection. They perform simple drive tasks. The motor starters provide a connection for mains supply and mains continuation as well as one or two connections for a three-phase asynchronous motor.
A complete motor starter consists of three products: motor starter, lower housing part, and Pg screw connection (see accessories).
- 2 integrated CONTACTRON hybrid motor starter with 3.0 kW
- Supported protocols: SNMPv2, TFTP, PROFINET IO, and LLDP
- 2 Ethernet connections
- 10 digital inputs (M12 sockets)
- 4 digital outputs (M12 sockets)
- Stainless steel housing with IP65/IP67 protection
Dimensions
| Width | 384 mm |
|---|---|
| Height | 182 mm |
| Depth | 139 mm |
| Note on dimensions | Module electronics without lower part |
| Drill hole spacing | 360 mm |
Ambient conditions
| Ambient temperature (operation) | -25 °C ... 50 °C (non-condensing) |
|---|---|
| Ambient temperature (storage/transport) | -25 °C ... 70 °C (non-condensing) |
| Permissible humidity (operation) | 0 % ... 85 % (non-condensing) |
| Permissible humidity (storage/transport) | 75 % (slight temporary condensation may sometimes appear on the housing) |
| Air pressure (operation) | 86 kPa ... 106 kPa (up to 2000 m above mean sea level) |
| Air pressure (storage/transport) | 86 kPa ... 106 kPa (up to 2000 m above mean sea level) |
| Degree of protection | IP67 in acc. with IEC 60529 |
Interfaces
| Fieldbus system | PROFINET |
|---|---|
| Connection method | 8-pos. RJ45 socket on motor starter |
| Designation connection point | X30 and X31 |
| Number of positions | 8 |
| Permissible conductor cross section | max. 0.14 mm² ... 0.22 mm² |
Power supply for module electronics
| Connection method | COMBICON |
|---|---|
| Designation | Terminal strip X13 |
| Number of positions | 3 |
| Permissible conductor cross section | 1.5 mm² |
| Pg screw connection | Pg11 |
| Supply voltage | 24 V DC (US1 / US2) |
| Supply voltage range | 20 V DC ... 30 V DC (including ripple) |
| Ripple | Permissible ripple 3.6 Vpp within the permissible voltage range |
| Supply current | typ. 0.25 A (at US1 = 24 V; plus current of digital inputs/outputs) |
| Max. current carrying capacity | 10 A |
Mains connection
| Designation | Mains connection |
|---|---|
| Connection method | POWER-COMBICON with silver contacts |
| Designation connection point | X11 |
| Number of positions | 5 |
| Permissible conductor cross section | 2.5 mm² ... 4 mm² |
| Pg screw connection | Pg11 |
| Operating voltage | 360 V AC ... 550 V AC (line voltage 50/60 Hz) |
| Max. current carrying capacity | 25 A |
Motor starter, output
| Connection method | POWER-COMBICON |
|---|---|
| Number | 2 |
| Designation connection point | Terminal strip; X10 and X12 |
| Permissible conductor cross section | 2.5 mm² ... 4 mm² |
| Pg screw connection | Pg16 |
| Operating voltage | 360 V AC ... 550 V AC (line voltage 50/60 Hz) |
| Frequency range | 50 Hz ... 60 Hz (mains frequency) |
| Nominal current range | 2.4 A ... 6 A |
| Utilization category | On the basis of AC 3 |
| Switching rate | 5 cycles per minute, maximum |
Motor monitoring
| Parameterization | via PROFINET |
|---|---|
| Parameterization range | 2.4 A ... 6 A |
Digital inputs
| Input name | Digital inputs |
|---|---|
| Number of inputs | 10 |
| Connection method | M12 connector |
| 2, 3, 4-wire | |
| Number of positions | 5 |
| Input voltage | 24 V DC (US1) |
| Input voltage range "0" signal | -3 V DC ... 5 V (binary "0") |
| Input voltage range "1" signal | 15 V DC ... 30 V DC (binary "1") |
| Typical input current per channel | approx. 3 mA (for US1 = 24 V) |
| Filter time | 3 ms |
| Power supply for sensors | UINI = US1 minus 1 V 500 mA Short-circuit/overload protection |
Digital outputs
| Output name | Digital outputs |
|---|---|
| Number of outputs | 4 |
| Connection method | M12 connector |
| 2-wire | |
| Number of positions | 5 |
| Output current | max. 500 mA (per channel) |
| Minimum output voltage with nominal current | US2 minus 1 V |
| Type of protection | Electronic short-circuit/overload protection, damping diode |
General
| Net weight | 3500 g |
|---|---|
| Note on weight specifications | Module electronics without lower part |
| Mounting type | Wall mounting |
| Note | Notes on operation Line protection for the power cable, maximum 25 A. Observe derating of the POWER COMBICON connector |
| Notes on operation Permitted network type TN network, TT network, IT network available on request |
Datasheet - PDF
▲| Title: | Size: | Type: |
|---|---|---|
| PHOENIX CONTACT-2701008-ELR 5030-2 IP PN | 110 Kbytes |
 |
Reviews (0) ▲
No customer reviews for the moment.
| Rating: |
|
| Name: | |
| Email: | |
| Subject: | |
| Text: | |
| Do you recommend this product to buy? | |
|
|
|
| Add review | |
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.