Selected parameters SYSTEM Through-beam HOUSING Ø10 - Ø20 SENSING RANGE 6 ... 20 m CONNECTION Cable OUTPUT External Amplifier MATERIAL Plastic Others SENSING RANGE 15 m HOUSING Ø11 x 24,5 mm MATERIAL PA6 ADDITIONAL Wireless Safety Edge
Wireless Entrapment Protection Device For Industrial Doors ESPE Type WSM/ WSS… • Wireless Entrapment Protection Device for Industrial Doors • Input for two ESPE (electro-sensitive protective equipment) • Replaces cable between Door controller and ESPE • Input for door-in-door sensor • Output ESPE: 1 x SPST NC, 1 x SPST NO (8,2kΩ) • Output low battery: 1 x SPST NC contact • 2,4 GHz duplex communication • Built-in antenna • IP66 ratings Product Description Ordering Key IC WSM2 B A 2 D24 Wireless EntrapmentProtec- tion Device (EPD) for Industrial Doors.Thesystemis designed to replace the con- nection cable between the ESPE (electro-sensitive pro- tective equipment) and the door controller. The sub con- troller has input for either N.C. ESPE, N.O. 8.2 kΩ ESPE or theCarloGavazzi lowcon- sumption photoelectric ESPE N.C. contact.The systemis designedforhighreliability using2.4 GHz duplexcom- munication between the main controllerand subcontroller. Themaincontrollercan handle up to 4 sub modules i.e. one system can handle 8 ESPEs. The sub controller is activated by a test signal from the main controller and stays active during the period of time set at the main controller up to 80 seconds. Function Main/Sub Controller No of channels Mute function Adjustment Output Power supply Type Selection Housing Range Type Orderingno. W x H x DWireless 75 x 125 x 35 mm 10 m Main Controller WSM 2 B A 2 D24 45 x 214 x 22 mm 10 m Sub ControllerWSS 2 B A 2 BAT Housing Range Cable length Type Orderingno. W x H x DSn Ø11 x 24.5 mm 15 m 2 mEmitterPB 11 CNT 15 WE Ø11 x 24.5 mm 15 m 12 mReceiver PB 11 CNT 15 WR Specifications Main Controller (WSM) Rated operational volt. (UB )12 to 24 VAC/DC (-10 +15%) Ripple (Urpp ) ≤ 10% Supply current < 50 mA Communication Frequency2.4 GHz Duplex Number of channels16 selectable via DIP switch Sub Controller live time10 – 80 sec. Selectable via DIP-switches Relay ESPE NC SPST ESPE NO 8.2 kΩSPST Low Battery SPST 1 A / 30 VDC 0,5 A / 30 VAC >100.000 AC11 or DC11 ProtectionReverse polarity, transients Indications Main Controller Power supply Green LED ESPE 1 or 2 active 2 x yellow LEDs Low Battery Red LED Channels not synchronized Toggle red & green LED Test input (active high or active low)Selectable via DIP switch Active high 12-24 V Active low0 V Test impulse time Minimum pulse width > 100 mS Maximum pulse width< 2 sec Operating frequency 25 Hz per sub controller Response time OFF-ON (tON)≤ 120 ms ON-OFF (tOFF ) ≤ 120 ms Specifications are subject to change without notice (03.01.2013) 1
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.