ZX-GTC11 238014 OMRON Advanced sensors, Amplifier NPN 3 digital outputs 1 analogue View larger
Images are for illustrative purposes only. Please refer to data sheet for details.

ZX-GTC11 238014 OMRON Advanced sensors, Amplifier NPN 3 digital outputs 1 analogue

ZX-GTC11

238014

OMRON

Available

Ship on today

Advanced sensors, Amplifier NPN 3 digital outputs 1 analogue

More details


Monitoring Products Measurement

Measurement sensors - Laser micrometer - OMRON

Measurement sensors - Laser micrometer - ZX-GT - OMRON

* Brand new produt in its original packing covered by the warranties and certifications provided by OMRON

QuantityPrice
1+$1,009.13
2+$1,006.08
*This price is per unit and is the net value (not including taxes if applicable).

There are several options for payment
- Credit card
- Wire Transfer
- PayPal


Related products

More info



ZX-GT Laser micrometer
Smart laser micrometer
• High accuracy: 5 to 10 μm
•All surfaces
• Long sensing distance: < 500 mm
• Line width up to 28 mm
• Calculation unit for multiple heads
• Fast sampling time: 0.5 ms
•PC software for setup
Ordering information
Sensors
TypeOptical system Measuring width Sensing distanceResolutionOutput type Order code
Separate type Through-beam28 mm 0 to 500 mm 10 μm NPNZX-GT28S11
PNP ZX-GT28S41
Integrated type 40 mm NPNZX-GT2840S11
PNP ZX-GT2840S41
Controller
Power supplyOutput type Order code
DCNPNZX-GTC11
PNP ZX-GTC41
Accessories (order separately)
Set of interface unit and setup software PCs
Output type Order code
Calculating units
Order code
NPN ZX-GIF11A PNP ZX-GIF41A
Interface unit(RS-232C/binary output)
Power supplyOutput type Order code
DCNPNZX-GIF11
PNP ZX-GIF41
Setup software PCs
Name Order code
Smart monitorGTZX-GSW11
Calculating unitZX-CAL2
Receiver-controller extension cable
Cable length Quantity Order code
Standard cableFlexible cable
1m1 m ZX-XGC1AZX-XGC1R
2mZX-XGC2AZX-XGC2R
5mZX-XGC5AZX-XGC5R
8mZX-XGC8AZX-XGC8R
20 mZX-XGC20A ZX-XGC20R
Up to two extension cables can be connected. However, be sure to limit the total extension cable length between the receiver and the controller to 30 meters (including the receiver cable).
397
ZX-GT Laser micrometer
Specifications
Sensor
Item ZX-GT28S11ZX-GT2840S11ZX-GT28S41ZX-GT2840S41
Output type NPNPNP
Appearance Separate type Integrated typeSeparate type Integrated type
Light source Visible semiconductor laser diode (wavelength 650 nm, CLASS 1 of EN60825-1/IEC60825-1, CLASS of FDA(21CFR 1040.10 and 1040.11)
Measuring width 28 mm
Sensing distance0 to 500 mm 40 mm 0 to 500 mm 40 mm
Minimum sensing object 0.5 mm dia.*1
Linearity ±0.1% F.S.*2
0.2 mm dia.0.5 mm dia.*10.2 mm dia.
Resolution 10 μm (number of process values to average: 16)*3
Temperature characteristic ±0.01% F.S/C*4
Indicators (emitter) Laser ON indicator (green), laser alarm indicator (red)
Indicator (receiver) Optical axis setting indicator (green)
Laser OFF input/sync inputON: Short-circuited with 0 V or 1.5 V max.
OFF: Open (leakage current: 0.1 mA max.)
Laser deterioration alarm output NPN open-collector output
30 VDC 20 mA max. Residual voltage 1.2 V max.
Power consumption (emitter) 30 mA max.
Power supply voltage (emitter) 24 VDC+10%, –15% ripple (p-p) 10% max.
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Insulation resistance 20 M (at 500VDC megger)
ON: Short-circuited with power supply voltage or power supply voltage -1.5 V max.
OFF: Open (leakage current: 0.1 mA max.)
PNP open-collector output
30 VDC 20 mA max. Residual voltage 2 V max.
Operating ambient illumination
(emitter)
Operating ambient illumination
(receiver)
3,000 lx (incandescent light)
1,000 lx (incandescent light)*5
Ambient temperatureOperating: 0 to 40°C, storage: –15 to 50°C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% (with no condensation)
Vibration resistance (durability) 10 to 150 Hz single-amplitude: 0.75 mm for 80 min each in X, Y and Z directions
Degree of protectionIEC60529 IP40
Cable length2m
Material Case: aluminum die-cast, Lens: glass
Weight (packed state)Approx. 550 g Approx. 570 g Approx. 550 g Approx. 570 g
AccessoriesLaser warning labels, instruction sheet
F.S.: 28 mm measuring range of receiver
*1Distance between emitter and receiver: 500 mm, measurement object at 250 mm from receiver. Glass ends of chamfer 0.1 mm or more can be detected in glass edge measurement mode. (at binary level 70%)
*2Linearity is given to be a typical error with respect to an ideal straight line when the distance between the emitter and receiver is 100 mm and light is blocked at a distance of 50 mm from the
receiver. (On the ZX-GT2840_, the measurement object is measured at a distance of 20 mm from the receiver.)
*3The amount of fluctuation (±3 ) in the analog output when the distance between the emitter and receiver is 100 mm and a ZX-GTC_ is connected
*4Change in the light cutoff value on one side when the distance between the emitter and receiver is 100 mm and the light is half-cutoff at a distance of 50 mm from the receiver (On the
ZX-GT2840_, the measurement object is measured at a distance of 20 mm from the receiver.)
*5Standard mode (NORM) used
Controller
Item ZX-GTC11ZX-GTC41
Output type NPNPNP
Measurement cycle*11.5 ms (standard mode (NORM))
0.5 ms (high-speed mode (FAST))*2
Samples to average 1/2/4/8/16/32/64/128/256/512/1024/2048/4096
Analog output*3 For current output: 4 to 20 mA/F.S., max. load resistance 300 
For voltage output: ±4 V, (±5 V, 1 to 5 V*4), output impedance 100 
Timing input, bank switching input, zero reset input, reset input
HIGH/PASS/LOW Judgment output*5
Sync output*6
ON: short-circuited with 0 V or 1.5 V max. OFF: Open (leakage current: 0.1 mA max.)
NPN open-collector output
30 VDC 50 mA max. Residual voltage 1.2 V max.
ON: short-circuited with power supply voltage or power supply voltage -1.5 V max.
OFF: Open (leakage current: 0.1 mA max.)
PNP open-collector output
30 VDC 50 mA max. Residual voltage 2 V max.
IndicatorJudgment output indicator: HIGH (orange), PASS (green), LOW (orange) Main display (red) sub-display (yellow) bank 1/2 (orange), zero reset (green)
Main functions
Number of registered setups
2 banks
Measurement mode Interrupted beam width measurement, incident beam width measurement, outer diameter measurement, center position measurement, IC lead pitch,
IC lead width judgment, specified edge measurement, wire position measurement, glass edge position measurement
Display during measurement
Measured value, resolution, threshold, voltage output value, current output value (number of display digits can be changed)
Zero reset functions Offset setting of zero reset value, zero reset value memory
Hold Sample hold, peak hold, bottom hold, peak-to-peak hold, average hold, delay hold
Timer functionsON-delay, OFF-delay, one-shot
Adjustment functionsOptical axis adjust mode/light intensityt writing mode, variable binary level, variable edge filter, analog output scaling
Calculation2 possible on up to two controllers (calculation Unit ZX-CAL2 is required for connecting controllers to each other.) A-B, A+B, width
OtherMeasurementcycle setting, threshold setting, hysteresis setting, initialization, key lock
398
ZX-GT Laser micrometer
Item ZX-GTC11 ZX-GTC41
Temperature characteristic ±0.005% F.S./°C
Current consumption 150 mA max. (including receiver)
Power supply voltage24 VDC+10%, –15% ripple (p-p) 10% max.
Dielectric strength 1,000 VAC, 50/60 Hz for min
Insulation resistance 20 M (at 500VDC megger)
Ambient temperatureOperating: 0 to 50°C, storage: –15 to 60°C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% (with no condensation)
Vibration resistance(durability)10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions
Degree of protectionIEC60529 IP20
Cable length2m
Material Case: PBT (polybutylene terephthalate), cover: Polycarbonate
Weight (packed state)Approx. 330 g
Accessories Instruction sheet
*1The first response time is “measurementcycle x (number of samples to average setting + 1) + 1 ms” max. For the second response time onwards, the specified measurement cycle time is output.
*2The response time in the high-speed mode (FAST) for the IC lead pitch and IC lead width judgment modes is 1 ms.
*3Current/voltage can be switched using the switch provided on the rear of the Controller.
*4Can be set by the analog output scaling function.
*5The error (ERR) state is displayed when all HIGH/PASS/LOW outputs turn OFF.
*6Normally, wire the sync output wire directly to the emitter's sync input wire and run the controller in the standard mode. On an NPN type controller, use an NPN type emitter, and on a PNP
type controller, use a PNP type emitter. Wiring of the sync wires is not required when the controller is run in the high-speed mode. (Note, however, that the controller becomes more susceptible to the influence of ambient light in this case.)
Interface unit
Item ZX-GIF11/-GIF11AZX-GIF41/-GIF41A Compatible controller ZX-GTC11ZX-GTC41
IndicatorPower ON (green), controller communications (orange), controller communications error (red), RS-232C communications (orange), RS-232C communications error (red), binary output (orange)
Communications portRS-232C (9-pin D-sub connector)
12-bit binary output
(D11 toD0, GATE)
NPN open-collector output
30 VDC 20 mA max. Residual voltage 1.2 V max.
PNP open-collector output
30 VDC 20 mA max. Residual voltage 2 V max.
Power supply voltageSupplied from controller (power consumption: 60 mA max.)
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Insulation resistance 20 M (at 500VDC megger)
Ambient temperatureOperating: 0 to 50°C, storage: –15 to 60°C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% (with no condensation)
Vibration resistance(durability)10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions
Degree of protectionIEC60529 IP20
Cable lengthRS-232C 0.5 m, binary output 2 m
Material Case: PBT (polybutylene terephthalate), cover: Polycarbonate
Weight (packed state)ZX-GIF_1A: Approx. 550 g
ZX-GIF_1: Approx.330 g
Accessories ZX-GIF_1A: Setup coftware (CD-ROM), 2 clamps, instruction sheet
ZX-GIF_1: 2 clamps, instruction sheet
399

Datasheet - PDF

Title:Language:Size:Type:
pdf1-mostradoController, NPN output - OMRON - ZX-GTC11 - 238014English171 Kbytespdf1-mostradoController, NPN output - OMRON - ZX-GTC11 - 238014
pdf1-Controller, NPN output - OMRON - ZX-GTC11 - 238014English5 Mbytespdf1-mostradoController, NPN output - OMRON - ZX-GTC11 - 238014
pdf2-mostradoController, NPN output - OMRON - ZX-GTC11 - 238014English3 Mbytespdf1-mostradoController, NPN output - OMRON - ZX-GTC11 - 238014
pdf3-mostradoController, NPN output - OMRON - ZX-GTC11 - 238014English499 Kbytespdf1-mostradoController, NPN output - OMRON - ZX-GTC11 - 238014

Reviews (0)

No customer reviews for the moment.

Add Review
hide form
Rating:
Name:
Email:
Subject:
Text:
  Captcha
  Add review