VC-MEMV-T1-R-M20 1886595 PHOENIX CONTACT Caixa Ver maior
As imagens são só a título ilustrativo. Por favor, consulte a ficha técnica.

VC-MEMV-T1-R-M20 1886595 PHOENIX CONTACT Caixa

VC-MEMV-T1-R-M20

1886595

PHOENIX_CONTACT

5

Caixa

Caixa aérea, Família de artigos: VARIOCON, construção: VC1, material da caixa: Fundição de zinco, cor: níquel. No uso de condutores de fibra óptica, os raios de curvatura do fabricante do cabo devem ser considerados.

Sleeve housing, Range of articles: VARIOCON, design: VC1, housing material: Zinc die-cast, color: nickel, When using fiber optics, the bending radii of the cable manufacturers must be observed.

Mais detalhes


Conexão de dispositivos de campo

Produto novo em sua embalagem original com todas as garantias e certificações de PHOENIX_CONTACT

* Este artigo pode estar obsoleto. Se você estiver interessado, insira seu e-mail e informaremos se há unidades disponíveis. Caso não existam mais, um dos nossos técnicos procurará uma alternativa fornecivel com características semelhantes.

Se o nosso preço não é o melhor, peça-nos uma cotação Solicitar uma cotação

Related products

Best sellers

Mais informação



Dados técnicos

Notes
GeneralWhen using fiber optics, the bending radii of the cable manufacturers must be observed.
Safety note
Safety noteWARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties
Product typeSleeve housings
Housing typeSleeve housing
Product familyVARIOCON
TypeVC1
No. of cable outlets1
Type of the screw connectionM20
Shieldedyes
Cable outletangled
Data management status
Article revision06

Connection data
Tightening torque1.2 ... 1.8 Nm

Dimensions
Dimensional drawinglwtokpfzcr.jpg
Width33 mm
Height65 mm
Length66 mm

Material specifications
Colornickel
Color of the housing partgray
MaterialDie-cast zinc (Housing)
NBR (O-ring)
Flammability rating according to UL 94V0
Seal materialEPDM, conductive
Housing materialZinc die-cast
O-ring materialNBR
Material of locking screwBrass, nickel-plated

Mechanical properties
Mechanical data
Type of the screw connectionM20
Locking typeScrew

Environmental and real-life conditions
Ambient conditions
Degree of protectionIP67 (IEC 60529)
IP65/IP66/IP67
Ambient temperature (operation)-40 °C ... 125 °C

ETIM for 1886595 Ligadores (EC000437)
Característica Valor
Largura (EF000008) 33 mm
Altura (EF000040) 65 mm
Profundidade (EF000049) 66 mm
Tipo de invólucro (EF006980) Caixa da ficha de ligação
Revestimento da estrutura (EF001601) Outro
Posição do estribo (EF008459) Nenhum
Com prensa-cabo (EF000735) Não
Método de montagem da prensa-cabo (EF012210) Métrico
Com tampa articulada (EF000117) Não
Com acolchoado (EF005072) Não
Com selo (EF005610) Não
Número de entradas de condutores (EF000437) 1
Tipo de fecho (EF000208) Parafuso
Temperatura de operação (EF002393) -40 °C
Versão EMC (EF001062) Não
Grau de proteção (IP), montado (EF007466) IP67

Datasheet - PDF

Avaliações: (0)

Não há comentários do produto ainda.

Adicionar avaliação
ocultar formulário
Avaliação:
Nome:
Email:
Título:
Opinión:
  Captcha
  Adicionar avaliação

Todas as classificações que recebemos a partir dos itens que oferecemos são reais e verificadas. Um pequeno gesto, mas muito valioso. Então, obrigado por esse minuto você gasta em deixar-nos a sua opinião e classificação de produtos, porque nos ajuda a continuar a melhorar e oferecer maior qualidade de serviço.