ANUNCIAR
VS-MSDBPS-OE-93G-LI/5,0 1419141 PHOENIX CONTACT Cabo de sistema Bus Ver maior
As imagens são só a título ilustrativo. Por favor, consulte a ficha técnica.

VS-MSDBPS-OE-93G-LI/5,0 1419141 PHOENIX CONTACT Cabo de sistema Bus

VS-MSDBPS-OE-93G-LI/5,0

1419141

PHOENIX_CONTACT

Cabo de sistema Bus

Conecte. ficha. para ser apar. parede de posters, EtherCAT® CAT5 (IEC11801:2002) (100 MBit/s), EtherCAT® CAT5 (100 MBit/s), 4 polos, PVC, verde RAL 6018, blindado, Conector macho, reto, M12-SPEEDCON, codificação: D, na extremidade livre do cabo, Montagem traseira, M16 x 1,5, Conexão do cabo, comprimento do cabo: 5 m, PVC flexível PROFINET CAT5, Produto alternativo de acordo com RoHS II sem exceção 6c (Pb< 0,1%) código do item: 1239232

Device connector rear mounting, EtherCAT® CAT5 (IEC 11801:2002) (100 Mbps), EtherCAT® CAT5 (100 Mbps), 4-position, PVC, green RAL 6018, shielded, Pin, straight, M12-SPEEDCON, coding: D, on free cable end, Rear mounting, M16 x 1.5, Cable connection, cable length: 5 m, PROFINET PVC stranded CAT5, Alternative product in accordance with RoHS II without Exemption 6c (Pb < 0.1 %) item no.: 1239232

Mais detalhes


Conectores > Condutor circular, de montagem (com fios)

Conexão de dispositivos de campo

Produto novo em sua embalagem original com todas as garantias e certificações de PHOENIX_CONTACT

Preço total: $90.84
Preço unitário: $90.84
Este preço é por unidade e mostra o valor líquido (excluindo impostos indirectos se aplicável).

Se o nosso preço não é o melhor, peça-nos uma cotação Solicitar uma cotação

Related products

Best sellers

Mais informação



Dados técnicos

Notes
Notes on operationThe electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
GeneralContact connection method: Crimp connection
Safety note
Safety noteWARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product properties
Product typeData cable preassembled
Sensor typeEtherCAT®
Number of positions4
No. of cable outlets1
Shieldedyes
CodingD
Thread typeM12
Data management status
Article revision08
Insulation characteristics
Overvoltage categoryII
Degree of pollution3

Interfaces
Bus systemEtherCAT®
Signal type/categoryEtherCAT® CAT5 (IEC 11801:2002), 100 Mbps
EtherCAT® CAT5 (IEC 11801), 100 Mbps

Electrical properties
Rated surge voltage2.5 kV
Contact resistance≤ 3 mΩ
Insulation resistance≥ 100 MΩ
Nominal voltage UN250 V
Nominal current IN4 A (Plug/socket in accordance with IEC 61076-2-101, cable technical data is to be observed)
Transmission mediumCopper
Transmission characteristics (category)CAT5 (IEC 11801:2002)

Mechanical properties
Mechanical data
Insertion/withdrawal cycles≥ 100

Material specifications
Flammability rating according to UL 94V0
Seal materialFKM
Contact materialCuZn
Contact surface materialNi/Au
Contact carrier materialPA 6.6
Material for screw connectionBrass, nickel-plated
Outer sheath, materialPVC

Connection data
Connection technology
Connection methodCable connection
Conductor connection
Contact connection typePin
Connection methodCable connection
Tightening torque2 Nm ... 3 Nm (Installation-side)

Connector
Connection 1
Head designPin
Head cable outletstraight
Head thread typeM12
Head locking typeSPEEDCON
CodingD
Connection 2
Head designfree cable end

Cable/line
Cable length5 m
PROFINET PVC stranded CAT5 [93B]
Desenho cotadoebkbgtwzch.jpg
Cable weight67 kg/km
UL AWM Style21694
Number of positions4
Shieldedyes
Cable typePROFINET PVC stranded CAT5 [93B]
Conductor structure1x4xAWG22/7, SF/TQ
Signal runtime5.3 ns/m
Signal speed0.66 c
Conductor structure signal line7x 0.25 mm
AWG signal line22
Conductor cross section4x 0.34 mm²
Wire diameter incl. insulation1.55 mm
External cable diameter6.50 mm ±0.2 mm
Outer sheath, materialPVC
External sheath, colorgreen RAL 6018
Conductor materialTin-plated Cu litz wires
Material wire insulationPE
Single wire, colorwhite, yellow, blue, orange
Thickness, outer sheathapprox. 0.90 mm
Overall twistStar quad
Optical shield covering85 %
Insulation resistance≥ 500 MΩ*km
Coupling resistance≤ 20.00 mΩ/m (at 10 MHz)
Loop resistance≤ 120.00 Ω/km
Wave impedance100 Ω ±15 Ω (at 100 MHz)
Nominal voltage, cable600 V
Test voltage Core/Core2000 V (50 Hz, 1 min.)
Test voltage Core/Shield2000.00 V (50 Hz, 1 min.)
Minimum bending radius, fixed installation3 x D
Minimum bending radius, flexible installation7 x D
Smallest bending radius, fixed installation20 mm
Smallest bending radius, movable installation46 mm
Near end crosstalk attenuation (NEXT)80 dB (with 1 MHz)
76 dB (at 4 МHz)
70 dB (at 10 MHz)
65 dB (at 16 MHz)
63 dB (at 20 МHz)
60 dB (at 31.25 МHz)
55 dB (at 62.5 МHz)
50 dB (at 100 MHz)
Shield attenuation2.1 dB (with 1 MHz)
4 dB (at 4 МHz)
6.3 dB (at 10 MHz)
8 dB (at 16 MHz)
9 dB (at 20 МHz)
11.4 dB (at 31.25 МHz)
16.5 dB (at 62.5 МHz)
21.3 dB (at 100 MHz)
Flame resistanceaccording to UL 1685 (CSA FT 4)
Resistance to oilResistant to oil to a limited extent
Other resistanceUV resistant (according to UL 1581, Section 1200)
Ambient temperature (operation)-40 °C ... 70 °C (cable, fixed installation)
-40 °C ... 70 °C (Cable, flexible installation)
Ambient temperature (installation)-20 °C ... 60 °C

Environmental and real-life conditions
Ambient conditions
Degree of protectionIP67 (When plugged in)
IP65 (When plugged in)
IP65/IP67
Ambient temperature (operation)-25 °C ... 85 °C (Plug / socket)
-40 °C ... 85 °C (without mechanical actuation)

Standards and regulations
M12
Standard designationM12 connector
Standards/specificationsIEC 61076-2-101

ETIM for 1419141 Ligadores (EC002635)
Característica Valor
Tipo de contacto (EF001587) Outro
Número de contatos de dados (EF012232) 0
Número de contatos de potência (EF012216) 0
Número de contatos de controlo (EF012217) 4
Tipo de invólucro (EF006980) Direito
Corrente nominal especificada In (EF008250) 4 A
Temperatura ambiente (EF002386) -25 °C
Tensão especificada de funcionamento (EF000228) 250 V
Categoria de sobretensão (I, II, III ou IV) (EF006785) II
Grau de poluição (1 a 4) (EF006786) 3
Material da superfície de contato (EF004020) Níquel
Material da caixa protetora (EF001596) Plástico
Material do anel roscado (EF012304) Outro
Tipo de fecho (EF000208) Outro
Classe de inflamabilidade do material de selagem de acordo com UL 94 (EF002521) V0
Com condutor de proteção (EF007468) Não
Grau de proteção (IP), montado (EF007466) IP67
Min. número de ciclos de inserção (EF012212) 100
Blindado (EF000881) Sim
Com indicação de estado (EF001602) Não

Datasheet - PDF

Avaliações: (0)

Não há comentários do produto ainda.

Adicionar avaliação
ocultar formulário
Avaliação:
Nome:
Email:
Título:
Opinión:
  Captcha
  Adicionar avaliação

Todas as classificações que recebemos a partir dos itens que oferecemos são reais e verificadas. Um pequeno gesto, mas muito valioso. Então, obrigado por esse minuto você gasta em deixar-nos a sua opinião e classificação de produtos, porque nos ajuda a continuar a melhorar e oferecer maior qualidade de serviço.