> PHOENIX_CONTACT>Fontes de alimentação>QUINT-PS- 24DC/24DC/10 2866378 PHOENIX CONTACT Transformador DC/DC
ANUNCIAR
Produto anterior Próximo produto
QUINT-PS- 24DC/24DC/10 2866378 PHOENIX CONTACT Transformador DC/DC Ver maior
As imagens são só a título ilustrativo. Por favor, consulte a ficha técnica.

QUINT-PS- 24DC/24DC/10 2866378 PHOENIX CONTACT Transformador DC/DC

QUINT-PS-24DC/24DC/10

2866378

PHOENIX_CONTACT

Transformador DC/DC

Transformador QUINT DC-DC, comutado primário, entrada: 24 V DC, saída: 24 V DC/10 A

QUINT DC/DC converter, primary-switched, input: 24 V DC, output: 24 V DC/10 A

Mais detalhes


Aparelhos elétricos de baixa tensão > Fonte de alimentação CC

Fontes de alimentação

Produto novo em sua embalagem original com todas as garantias e certificações de PHOENIX_CONTACT

Preço total: $657.59
Preço unitário: $657.59
Este preço é por unidade e mostra o valor líquido (excluindo impostos indirectos se aplicável).

Se o nosso preço não é o melhor, peça-nos uma cotação Solicitar uma cotação

Best sellers

▲

Mais informação

▲


Dados técnicos
Input data
Input voltage24 V DC
Nominal input voltage range24 V DC
Input voltage range18 V DC ... 32 V DC
Wide-range inputyes
Input voltage range DC18 V DC ... 32 V DC
Voltage type of supply voltageDC
Inrush current< 20 A (typical)
Inrush current integral (I2t)0.3 A2s
Frequency range DC0 Hz
Mains buffering time> 3 ms (24 V DC)
Current consumptiontyp. 11.4 A (24 V)
Protective circuitTransient surge protection; Varistor
Typical response time< 1 s
Input fuse25 A (slow-blow, internal)
Output data
Efficiency> 88 %
Nominal output voltage24 V DC ±1 %
Setting range of the output voltage (USet)22.5 V DC ... 28.5 V DC (> 24 V DC, constant capacity restricted)
Nominal output current (IN)10 A (-25 °C ... 60 °C)
Derating60 °C ... 70 °C (2.5 %/K)
Feedback voltage resistance35 V DC
Protection against overvoltage at the output (OVP)< 35 V DC
Max. capacitive loadunlimited
Active current limitationApprox. 18 A
Control deviation< 1 % (change in load, static 10 % ... 90 %)
< 2 % (change in load, dynamic 10 % ... 90 %)
< 0.1 % (change in input voltage ±10 %)
Residual ripple< 60 mVPP
Output power240 W
Maximum no-load power dissipation< 2 W
Power loss nominal load max.< 28 W
Rise time< 2 ms (UOUT(10 % ... 90 %))
Connection in parallelyes, for redundancy and increased capacity
Connection in seriesyes
Signal: DC OK active
Output descriptionUOUT> 21.5 V: High signal
Maximum switching voltage≤ 24 V DC
Output voltage+ 24 V DC
Continuous load current≤ 40 mA
Signal: DC OK floating
Output descriptionUOUT> 21.5 V: Contact closed
Maximum switching voltage≤ 30 V AC/DC
Continuous load current≤ 1 A
Connection data
Input
Connection methodPluggable screw connection
Conductor cross section, rigid min.0.2 mm²
Conductor cross section, rigid max.2.5 mm²
Conductor cross section flexible min.0.2 mm²
Conductor cross section flexible max.2.5 mm²
Conductor cross section AWG min.24
Conductor cross section AWG max.12
Stripping length7 mm
Screw threadM3
Tightening torque, min0.5 Nm
Tightening torque max0.6 Nm
Output
Connection methodPluggable screw connection
Conductor cross section, rigid min.0.2 mm²
Conductor cross section, rigid max.2.5 mm²
Conductor cross section flexible min.0.2 mm²
Conductor cross section flexible max.2.5 mm²
Conductor cross section AWG min.24
Conductor cross section AWG max.12
Stripping length7 mm
Screw threadM3
Tightening torque, min0.5 Nm
Tightening torque max0.6 Nm
Signal
Conductor cross section, rigid min.0.2 mm²
Conductor cross section, rigid max.2.5 mm²
Conductor cross section flexible min.0.2 mm²
Conductor cross section flexible max.2.5 mm²
Conductor cross section AWG min.24
Conductor cross section AWG max.12
Screw threadM3
Tightening torque, min0.5 Nm
Tightening torque max0.6 Nm
Signaling
Types of signalingLED
Active switching output
Operating voltage displayGreen LED
Signal output: DC OK active
Status display"DC OK" LED green
Signal output: DC OK floating
Status display"DC OK" LED green
Electrical properties
Number of phases1.00
Insulation voltage input/output1 kV (routine test)
1.5 kV (type test)
Product properties
Product typeDC/DC converters
MTBF (IEC 61709, SN 29500)> 500000 h
Data management status
Article revision06
Insulation characteristics
Protection classIII
Degree of pollution2
Dimensions
Dimensional drawingnlaasavpqp.jpg
Width80 mm
Height130 mm
Depth125 mm
Installation dimensions
Installation distance right/left0 mm / 0 mm (≤ 70 °C)
Installation distance right/left (active)15 mm / 15 mm (≤ 70 °C)
Installation distance top/bottom50 mm / 50 mm (≤ 70 °C)
Installation distance top/bottom (active)50 mm / 50 mm (≤ 70 °C)
Alternative assembly
Width122 mm
Height130 mm
Depth83 mm
Mounting
Assembly notealignable: horizontally 0 mm, vertically 50 mm
Mounting positionhorizontal DIN rail NS 35, EN 60715
With protective coatingno
Material specifications
Housing materialMetal
Type of housingAluNox (AlMg1)
Environmental and real-life conditions
Ambient conditions
Degree of protectionIP20
Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)-40 °C ... 85 °C
Climatic class3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)95 % (at 25 °C, non-condensing)
Shock18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)< 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6)
15 Hz ... 150 Hz, 2.3g, 90 min.
Standards and regulations
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)
Standard - Electrical safetyEN 60950-1/VDE 0805 (SELV)
Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178
Standard – Safety extra-low voltageEN 60950-1 (SELV)
EN 60204 (PELV)
Standard - Safe isolationDIN VDE 0100-410
Standard - Safety of transformersEN 61558-2-17
Approvals
Shipbuilding approvalDNV GL (EMC A), ABS
UL approvalsUL/C-UL listed UL 508
UL/C-UL Recognized UL 60950-1
UL/C-UL Listed UL 1604 Class I, Division 2, Groups A, B, C, D
EMC data
Electromagnetic compatibilityConformance with EMC directive 89/336/EC
Noise immunityEN 61000-6-2:2005
Electrostatic discharge
Standards/regulationsEN 61000-4-2
HousingLevel 3
Electrostatic discharge
Contact discharge8 kV
Discharge in air8 kV
CommentsCriterion B
Electromagnetic HF field
Standards/regulationsEN 61000-4-3
Electromagnetic HF field
Frequency range80 MHz ... 2 GHz
Test field strength10 V/m
CommentsCriterion A
Fast transients (burst)
Standards/regulationsEN 61000-4-4
Fast transients (burst)
Input2 kV (Level 3 - asymmetrical)
Output2 kV (Level 3 - asymmetrical)
Signal1 kV (Level 2 - asymmetrical)
Surge voltage load (surge)
Standards/regulationsEN 61000-4-5
Surge voltage load (surge)
CommentsCriterion B
Input/Output2 kV (Level 3 - asymmetrical)
Input/Output/Signal1 kV (Level 3 - asymmetrical)
Conducted interference
Standards/regulationsEN 61000-4-6
Conducted interference
I/O/SLevel 3 - asymmetrical
Frequency range0.15 MHz ... 80 MHz
CommentsCriterion A
Voltage10 V
Voltage dips
Standards/regulationsEN 61000-4-11
Emitted interference
Standards/regulationsEN 61000-6-3
Radio interference voltage in acc. with EN 55011EN 55011 (EN 55022) Class B, area of application: Industry and residential
Emitted radio interference in acc. with EN 55011EN 55011 (EN 55022) Class B, area of application: Industry and residential

Datasheet - PDF

▲
Título: Tamanho: Tipo:
PDF CATALOG PHOENIX PROTECTION EN .pdf 27 Mbytes
PHOENIX CONTACT-2866378-QUINT-PS- 24DC/24DC/10 126 Kbytes PHOENIX CONTACT-2866378-QUINT-PS- 24DC/24DC/10

Avaliações: (0) ▲

Não há comentários do produto ainda.

Adicionar avaliação
Adicionar avaliação
ocultar formulário
Avaliação:
Nome:
Email:
Título:
Opinión:
Você recomendaria esse produto para comprar?
  Captcha
  Adicionar avaliação

Últimas opiniões dos nossos clientes

Todas as classificações que recebemos a partir dos itens que oferecemos são reais e verificadas. Um pequeno gesto, mas muito valioso. Então, obrigado por esse minuto você gasta em deixar-nos a sua opinião e classificação de produtos, porque nos ajuda a continuar a melhorar e oferecer maior qualidade de serviço.