SIEMENS

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): 2 inch NPT ((Taper), ASME B1.20.1) Antenna Extention: 150 mm (6 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: PROFIBUS PA Approvals: Ordinary Locations/General Purpose (Non-Ex), CE, UKCA, RED, RCM Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna Material: PTFE Process Connection Thread Connection (316L Stainless Steel): 2" NPT ((Conical), ANSI/ASME B1.20.1) Antenna Extender: 150 mm (6"), Extension, 1.4404/316L Stainless Steel Screen Gasket: FKM O-Ring, Not Available for Flat Flange Combined with Antenna Options 0, 1, 2 Cable Box/Entry: Epoxy Coated Aluminum 2 x 1/2" NPT, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: Standard, CE includes European Radio approvals (R&TTE;) 5.8 GHz nominal pressure: According to the pressure/temperature curves of the Service Instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): 2 inch NPT ((Taper), ANSI/ASME B1.20.1) Antenna Extention: 150 mm (6 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: PROFIBUS PA Approvals: General Purpose, CE, RED, RCM Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE connection to the process thread connection (316L stainless steel): 2" NPT ((conical), ANSI/ASME B1.20.1) Antenna extender: without antenna extender gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens User Interface LUI (Local User Interface) communication/output: 4 ... 20 mA, HART, start with <3.6 mA approvals: ATEX II 1/2 G EEx em ia IIC T4, no barrier required nominal pressure: 0.5 bar (7.25 psi) maximum

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): 2 inch NPT ((Taper), ANSI/ASME B1.20.1) Antenna Extension: No antenna extension Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Increased Safety, ATEX II 1/2G Ex embia IIC T4 Ga/Gb, CE, RED, RCM; GOST-R Pressure rating: 0.5 bar (7.25 psi)maximum

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: 1" NPT (Taper), ANSI/ASME B1.20.1 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: 1" NPT (tapered), ANSI/ASME B1.20.1 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP68 Active Shield Length: Extended Display - (250 mm Thread, 230 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: 1" NPT (Taper), ANSI/ASME B1.20.1 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: R 1" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr. A, B, C, D, E, F, G T4 or T6 Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: R 1" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP65 Active Shield Length: Extended Display - (400 mm Thread, 380 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: R 1" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP65 Active Shield Length: Extended Shield - (400 mm threaded, 380 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP68 Active Shield Length: Standard Length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: G 1" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Extended rod, length 500 mm (19.69") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: G 1" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe length: (length from flange face) Rod extension, length 500 mm (19.69") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CE, C-TICK, ATEX II 1 G EEx ia IIC T6... T4, ATEX II 1/2 D IP6X T100 C Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP65 Active Shield Length: Standard Length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: G 1" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Extended rod, length 500 mm (19.69") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CE, C-TICK, ATEX II 1 G EEx ia IIC T6...T4, ATEX II 1/2 D I IP6X T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): 2 inch NPT ((Taper), ASME B1.20.1) Antenna Extention: 100 mm (4 inch) extension, PTFE Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: PROFIBUS PA Approvals: Ordinary Locations/General Purpose (Non-Ex),CSA, FM, IC, FCC Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna Material: PTFE Process Connection Thread Connection (316L Stainless Steel): 2" NPT ((Conical), ANSI/ASME B1.20.1) Antenna Extender: 100 mm (4"), Extension, PTFE Gasket: FKM O-Ring, Not Available for Flat Flange Combined with Antenna Options 0, 1, 2 Cable Box/Entry: Epoxy Coated Aluminum 2 x 1/2" NPT, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: Standard, CSA US/C FM, 6.3 GHz, nominal pressure: According to the pressure/temperature curves of the operating instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): 2 inch NPT ((Taper), ANSI/ASME B1.20.1) Antenna Extention: 100 mm (4 inch) extension, PTFE Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: PROFIBUS PA Approvals: General Purpose,CSA, FM, Industry Canada, FCC Pressure rating: rating per pressure/temperature curves in instruction manual

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: G 1 1/2"(BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, UKCA, RCM, ATEX, UKEX II 1/2G Ex ia/db; ATEX, UKEX II 1/2D Ex ia/tb Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: G 1 1/2" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe length: (length from flange face) Rod extension, length 750 mm (29.53") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof, fire-resistant enclosure with intrinsic safety probe (IS) CE probe, C-tick, ATEX II 1/2 G EEx d(ia) IIC T6... T4, ATEX II 1/2 D T100 C Case & Lid: Aluminium, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP68 Active Shield Length: Enlarged Display - (400 mm Thread, 380 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: G 1 1/2"(BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, C-TICK, ATEX II 1/2 G EEx d(ia) IIC T6...T4, ATEX II 1/2 D T100 C Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP68 Active Shield Length: Extended Shield - (400 mm threaded, 380 mm flanged)

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): R 2 inch ((BSPT) (EN 10226-1) Antenna Extention: 200 mm (8 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: PROFIBUS PA Approvals: Intrinsically Safe, FM Class I, II, Div 1, Groups A, B, C, D, E, F, G, FCC Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE connection to the process thread connection (316L stainless steel): R 2" ((BSPT), EN 10226-1) Antenna extender: 200 mm (8"), extension, stainless steel screen 1.4404/316L gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: FM, class I and II, Div I, group A-G, 6.3 GHz degree of protection intrinsic safety (IS) with appropriate barrier nominal pressure: According to the pressure/temperature curves of the Service Instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): G 2 inch ((BSPP), EN ISO 228-1) Antenna Extention: 200 mm (8 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: PROFIBUS PA Approvals: Ordinary Locations/General Purpose (Non-Ex),CSA, FM, IC, FCC Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE process connection thread connection (316L stainless steel): G 2" ((BSPP), EN ISO 228-1) Antenna extender: 200 mm (8"), extension, stainless steel screen 1.4404/316L gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable box/entry: Epoxy coated aluminum 2 x 1/2" NPT, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: Standard, CSA US/C FM, 6.3 GHz, nominal pressure: According to the pressure/temperature curves of the operating instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): G 2 inch ((BSPP), EN ISO 228-1) Antenna Extention: 200 mm (8 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: PROFIBUS PA Approvals: General Purpose,CSA, FM, Industry Canada, FCC Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): 6 inch ASME, 150 lb, flat faced Antenna Extention: 250 mm (10 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Ordinary Locations/General Purpose (Non-Ex),CSA, FM, IC, FCC Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna Material: PTFE Process Connection Flat Flanges (316L Stainless Steel): 6" ASME 150 lb, Flat Flange Antenna Extender: 250 mm (10"), 1.4404/316L Stainless Steel Screen Extension Gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable Box/Entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens User Interface LUI (Local User Interface) communication/output: 4 ... 20 mA, HART, start with <3.6 mA approvals: Standard, CSA US/C FM, 6.3 GHz, nominal pressure: According to the pressure/temperature curves in the operating instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): 6 inch ASME, 150 lb, flat faced Antenna Extention: 250 mm (10 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: General Purpose,CSA, FM, Industry Canada, FCC Pressure rating: rating per pressure/temperature curves in instruction manual

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 1" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 500 mm (19.69") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose CSA, FM, CE, UKCA, RCM Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 1" Sealed Slat, 600 lb Probe Length: (length from flange face) Rod extension, length 500 mm (19.69") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: General purpose (CSA, FM, CE, C-TICK) Case and lid: aluminum, epoxy coated, 2 x M20 x 1.5 Cable entry, IP68 Active Shield length: Standard length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 1" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 500 mm (19.69") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose (CSA, FM, CE, C-TICK) Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP68 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 1 1/2" ASME, 300 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose CSA, FM, CE, UKCA, RCM Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 1 1/2" Sealed Slat, 300 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: General purpose (CSA, FM, CE, C-TICK) Case and lid: aluminum, epoxy coated, 2 x M20 x 1.5 Cable entry, IP65 Active Shield length: Extended display - (400 mm thread, 380 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 1 1/2" ASME, 300 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose (CSA, FM, CE, C-TICK) Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP65 Active Shield Length: Extended Shield - (400 mm threaded, 380 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 300 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 3" Sealed Slat, 300 lb Probe Length: (length from flange face) Rod extension, length 750 mm (29.53") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP68 Active Shield Length: Extended Display - (250 mm Thread, 230 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 300 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 3" Sealed Slat, 600 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP65 Active Shield Length: Extended Display - (250 mm thread, 230 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 4" ASME, 150 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 4" Sealed Slat, 150 lb Probe Length: (length from flange face) Rod extension, length 750 mm (29.53") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP65 Active Shield Length: Standard Length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 4" ASME, 150 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 40, PN 40 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side joints: Graphite Probe material: stainless steel, mat no. 1...

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 40, PN 40 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof, fire-resistant enclosure with intrinsic safety probe (IS) CE probe, C-tick, ATEX II 1/2 G EEx d(ia) IIC T6... T4, ATEX II 1/2 D T100 C Case & Lid: Aluminium, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP65 Active Shield Length: Extended Display - (250 mm Thread, 230 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 40, PN 40 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, C-TICK, ATEX II 1/2 G EEx d(ia) IIC T6...T4, ATEX II 1/2 D T100 C Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 50, PN 16 Probe length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: stainless steel, mat no. 1...

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 50, PN 16 Probe length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof, fire-resistant enclosure with intrinsic safety probe (IS) CE probe, C-tick, ATEX II 1/2 G EEx d(ia) IIC T6... T4, ATEX II 1/2 D T100 C Case & Lid: Aluminum, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP65 Active Shield Length: Standard Length - (125 mm Thread, 105 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 50, PN 16 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, C-TICK, ATEX II 1/2 G EEx d(ia) IIC T6...T4, ATEX II 1/2 D T100 C Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP65 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 50, PN 40 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Explosion Proof with IS Probe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 50, PN 40 Probe length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof enclosure (explosion protected) with intrinsically safe (IS) CSA/FM Probe Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Class III T4 Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Extended display - (400 mm thread, 380 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 50, PN 40 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Explosion Proof with IS Probe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Extended Shield - (400 mm threaded, 380 mm flanged)

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna Material: PTFE Process Connection Flat Flanges (316L Stainless Steel): DN 150 PN 40, Flat Flange Antenna Extender: 150 mm (6"), Extension, 1.4404/316L Stainless Steel Screen Gasket: FKM O-ring, not available for Flat Flange combined with antenna options 0, 1, 2 Cable Box/Entry: Epoxy coated aluminum 2 x 1/2" NPT, Siemens User Interface LUI (Local User Interface) communication/output: 4 ...

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna Material: PTFE Process Connection Flat Flanges (316L Stainless Steel): DN 150 PN 40, Flat Flange Antenna Extender: 150 mm (6"), Extension, 1.4404/316L Stainless Steel Screen Gasket: FKM O-ring, not available for Flat Flange combined with antenna options 0, 1, 2 Cable Box/Entry: Epoxy coated aluminum 2 x 1/2" NPT, Siemens User Interface LUI (Local User Interface) communication/output: 4 ... 20 mA, HART, start with <3.6 mA Approvals: ATEX II 1 G EEx (ia) IIC T4, intrinsically safe degree with appropriate barrier Nominal pressure: According to the pressure/temperature curves in the operating instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): DN 150 PN 40, Type B1, flat faced Antenna Extention: 150 mm (6 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Intrinsically Safe, IECEx/ATEX II 1G Ex ia IIC T4, INMETRO Ex ia IIC T4, CE, RED, RCM GOST-R Pressure rating: rating per pressure/temperature curves in instruction manual

Pointek CLS300 RF Capacitance point level switch, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. Process Connection: 3/4" NPT (Taper), ANSI/ASME B1.20.1 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose CSA, FM, CE, UKCA, RCM Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shiled Length: Extended Shield - (250 mm threaded, 230 mm flanged)

. Pointek CLS300 RF Capacitive Level Switch, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. Process connection: 3/4" NPT (tapered), ANSI/ASME B1.20.1 Special version: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: General purpose (CE, C-TICK) Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Extended display - (250 mm thread, 230 mm flange)

Pointek CLS300 RF Capacitance point level switch, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. Process Connection: 3/4" NPT (Taper), ANSI/ASME B1.20.1 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose, CE, C-TICK Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shiled Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 1 1/2" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 1 1/2" Waterproof Slat, 600 lb Probe Length: (length from flange face) Rod extension, length 750 mm (29.53") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: General purpose (CSA, FM) Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Extended display - (400 mm thread, 380 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 1 1/2" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose (CSA, FM) Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Extended Shield - (400 mm threaded, 380 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: G 3/4" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Standard version, rod 350 mm (13.78") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: G 3/4" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe length: (length from flange face) Standard, 350 mm (13.78") rod Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Ex protection for CE dust, C-TICK, ATEX II 1/2 D, 2 D IP6X T100 C Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Standard length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: G 3/4" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Standard version, rod 350 mm (13.78") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Dust Ignition Proof CE, C-TICK, ATEX II 1/2 D, 2 D IP6X T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 3" Sealed Slat, 600 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: Explosion-proof, fire-resistant enclosure with intrinsic safety probe (IS) CE probe, C-tick, ATEX II 1/2 G EEx d(ia) IIC T6... T4, ATEX II 1/2 D T100 C Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Extended display - (250 mm thread, 230 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, C-TICK, ATEX II 1/2 G EEx d(ia) IIC T6...T4, ATEX II 1/2 D T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): DN 50 PN 16, Type A, flat faced Antenna Extention: 50 mm (2 inch) extension, PTFE Process Seal/Gasket: Integral Gasket, for FF flange process connections only, not for Antenna options 3,4,5,6 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Increased Safety: ATEX II 1/2G Ex eb mb ia IIC T4 Ga/Gb; UKEX II 1/2G Ex eb mb ia IIC T4 Ga/Gb; CE, UKCA, RED, RCM, EAC Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE Process connection Flat flanges (316L stainless steel): DN 50 PN 16, Type A, flat flange Antenna extender: 50 mm (2") extension, PTFE gasket: Integrated gasket, only for flat flange process connections, not for antenna options 3-6 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens User Interface LUI (Local User Interface) communication/output: 4 ... 20 mA, HART, start with <3.6 mA approvals: ATEX II 1/2 G EEx em ia IIC T4, no nominal pressure barrier required: According to the pressure/temperature curves in the operating instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): DN 50 PN 16, Type A, flat faced Antenna Extention: 50 mm (2 inch) extension, PTFE Process Seal/Gasket: Integral Gasket, for FF flange process connections only, not for Antenna options 3,4,5,6 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Increased Safety, ATEX II 1/2G Ex embia IIC T4 Ga/Gb, CE, RED, RCM; GOST-R Pressure rating: rating per pressure/temperature curves in instruction manual

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, UKCA, RCM, ATEX, UKEX II 1/2G Ex ia/db; ATEX, UKEX II 1/2D Ex ia/tb Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof, fire-resistant enclosure with intrinsic safety probe (IS) CE probe, C-tick, ATEX II 1/2 G EEx d(ia) IIC T6... T4, ATEX II 1/2 D T100 C Case and lid: aluminium, epoxy coated, 2 x M20 x 1.5 Cable entry, IP68 Active Shield length: Enlarged display - (250 mm thread, 230 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, C-TICK, ATEX II 1/2 G EEx d(ia) IIC T6...T4, ATEX II 1/2 D T100 C Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP68 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 150 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Explosion Proof with IS Probe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 3" Waterproof Slat, 150 lb Probe Length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof enclosure (explosion protected) with intrinsically safe (IS) CSA/FM Probe Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Class III T4 Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Extended display - (250 mm thread, 230 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 150 lb Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Explosion Proof with IS Probe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries.

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE Process connection Flat flanges (316L stainless steel): DN 80 PN 16, Type A, flat flange Antenna extender: without antenna extender gasket: Integrated gasket, only for flat flange process connections, not for antenna options 3-6 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: Standard, CE includes European Radio approvals (R&TTE;) 5.8 GHz nominal pressure: According to the pressure/temperature curves of the Service Instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): DN 80 PN 16, Type A, flat faced Antenna Extension: No antenna extension Process Seal/Gasket: Integral Gasket, for FF flange process connections only, not for Antenna options 3,4,5,6 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: PROFIBUS PA Approvals: General Purpose, CE, RED, RCM Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): DN 80 PN 16, Type A, flat faced Antenna Extention: 250 mm (10 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Intrinsically Safe, CSA Class I, II, Div 1, Groups A,B,C,D,E,F,G, Industry Canada Pressure rating: 0.5 bar (7.25 psi)maximum

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE Process connection Flat flanges (316L stainless steel): DN 80 PN 16, Type A, flat flange Antenna extender: 250 mm (10"), stainless steel screen extension 1.4404/316L gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens LUI (Local User Interface) communication/output: 4 ... 20 mA, HART, <3.6 mA start Approvals: CSA Class I and II Div. I, Group A,B,C,D,G, intrinsically safe (IS) degree of protection with appropriate barrier Pressure rating: 0.5 bar (7.25 psi) maximum

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): DN 100 PN 16, Type A, flat faced Antenna Extention: 200 mm (8 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: PROFIBUS PA Approvals: Intrinsically Safe, CSA Class I, II, Div 1, Groups A,B,C,D,E,F,G, Industry Canada Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE Process connection Flat flanges (316L stainless steel): DN 100 PN 16, Type A, flat flange Antenna extender: 200 mm (8"), extension, stainless steel screen 1.4404/316L gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable box/entry: Epoxy coated aluminum 2 x 1/2" NPT, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: CSA class I and II Div. I, Group A,B,C,D,G, degree of protection intrinsic safety (IS) with appropriate barrier nominal pressure: According to the pressure/temperature curves of the Service Instructions

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 1" Sealed Slat, 300 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 1" Sealed Slat, 300 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: Explosion-proof enclosure (explosion protected) with intrinsically safe (IS) CSA/FM Probe Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP65 Active Shield Length: Standard Length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 1" ASME, 300 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Explosion Proof with IS Probe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): R 2 inch ((BSPT) (EN 10226-1) Antenna Extention: 150 mm (6 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: PROFIBUS PA Approvals: Ordinary Locations/General Purpose (Non-Ex), CE, UKCA, RED, RCM Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE process connection thread connection (316L stainless steel): R 2" ((BSPT), EN 10226-1) Antenna extender: 150 mm (6"), extension, stainless steel screen 1.4404/316L gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: Standard, CE includes European Radio approvals (R&TTE;) 5.8 GHz nominal pressure: According to the pressure/temperature curves of the Service Instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection threaded connection (316L stainless steel): R 2 inch ((BSPT) (EN 10226-1) Antenna Extention: 150 mm (6 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: PROFIBUS PA Approvals: General Purpose, CE, RED, RCM Pressure rating: rating per pressure/temperature curves in instruction manual

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 4" Waterproof Slat, 150 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat. No. 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 4" Waterproof Slat, 150 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat. No. 1.4404/316L with ceramic insulators Approvals: Ex protection for CE dust, C-tick, Atex II 1/2 D, 2 D IP6X T100 C Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP68 Active Shield length: Standard length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 4" ASME, 150 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Dust Ignition Proof CE, C-TICK, ATEX II 1/2 D, 2 D IP6X T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 25, PN 16 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 25, PN 16 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof enclosure (explosion protected) with intrinsically safe (IS) CSA/FM Probe Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Class III T4 Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Extended display - (400 mm thread, 380 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 25, PN 16 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Explosion Proof with IS Probe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Extended Shield - (400 mm threaded, 380 mm flanged)

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: 1" NPT (tapered), ANSI/ASME B1.20.1 Probe length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: stainless steel, mat no. 1. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: 1" NPT (tapered), ANSI/ASME B1.20.1 Probe length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof enclosure (explosion protected) with intrinsically safe (IS) CSA/FM Probe Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP65 Active Shield Length: Extended Display - (250 mm Thread, 230 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: 1" NPT (Taper), ANSI/ASME B1.20.1 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Explosion Proof with IS Probe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

. Pointek CLS300 RF Capacitive Level Switch, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. Process connection: 3/4" NPT (tapered), ANSI/ASME B1.20.1 Special version: (length from flange face) Rod extension, length 750 mm (29.53") Process side seals: Graphite Probe material: stainless steel, mat no. 1.

. Pointek CLS300 RF Capacitive Level Switch, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. Process connection: 3/4" NPT (tapered), ANSI/ASME B1.20.1 Special version: (length from flange face) Rod extension, length 750 mm (29.53") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Ex protection for dust with intrinsically safe (IS) probe: CE, C-TICK, ATEX II 1/2 D T100 C Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP68 Active Shield length: Extended screen - (250 mm thread, 230 mm flange)

Pointek CLS300 RF Capacitance point level switch, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. Process Connection: 3/4" NPT (Taper), ANSI/ASME B1.20.1 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Dust Ignition Proof with IS Probe: CE, C-TICK, ATEX II 1/2 D T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shiled Length: Extended Shield - (250 mm threaded, 230 mm flanged)

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): 3 inch ASME, 300 lb, flat faced Antenna Extention: 50 mm (2 inch) extension, PTFE Process Seal/Gasket: Integral Gasket, for FF flange process connections only, not for Antenna options 3,4,5,6 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: 4-20mA HART, start-up at <3.

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna Material: PTFE Process Connection Flat Flanges (316L Stainless Steel): 3" ASME 300 lb, Flat Flange Antenna Extender: 50 mm (2") Extension, PTFE Gasket: Integrated Gasket, Flat Flange Process Connections Only, Not for 3-6 Antenna Options Cable Box/Entry: Epoxy Coated Aluminum 2 x 1/2" NPT, Siemens LUI (Local User Interface) User Interface Communication/Output: 4 ... 20 mA, HART, start with <3.6 mA Approvals: ATEX II 1 G EEx (ia) IIC T4, intrinsically safe degree with appropriate barrier Nominal pressure: According to the pressure/temperature curves in the operating instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): 3 inch ASME, 300 lb, flat faced Antenna Extention: 50 mm (2 inch) extension, PTFE Process Seal/Gasket: Integral Gasket, for FF flange process connections only, not for Antenna options 3,4,5,6 Enclosure/Cable inlet: Aluminum, Epoxy painted, 2 x 1/2" NPT, Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Intrinsically Safe, IECEx/ATEX II 1G Ex ia IIC T4, INMETRO Ex ia IIC T4, CE, RED, RCM GOST-R Pressure rating: rating per pressure/temperature curves in instruction manual

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 50, PN 16 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 50, PN 16 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP65 Active Shield Length: Extended Display - (250 mm Thread, 230 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 50, PN 16 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose CSA, FM, CE, UKCA, RCM Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 3" Sealed Slat, 600 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: General purpose (CSA, FM, CE, C-TICK) Case and lid: aluminum, epoxy coated, 2 x M20 x 1.5 Cable entry, IP68 Active Shield length: Standard length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose (CSA, FM, CE, C-TICK) Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP68 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, UKCA, RCM, ATEX, UKEX II 1/2G Ex ia/db; ATEX, UKEX II 1/2D Ex ia/tb Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Explosion-proof, fire-resistant enclosure with intrinsic safety probe (IS) CE probe, C-tick, ATEX II 1/2 G EEx d(ia) IIC T6... T4, ATEX II 1/2 D T100 C Case & Lid: Aluminium, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP68 Active Shield Length: Standard Length - (125mm Thread, 105mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: R 1 1/2" (BSPT), EN 10226/PT (JIS-T), JIS B 0203 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Flameproof Enclosure with IS Probe: CE, C-TICK, ATEX II 1/2 G EEx d(ia) IIC T6...T4, ATEX II 1/2 D T100 C Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP68 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries.

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE Process connection Flat flanges (316L stainless steel): DN 80 PN 16, Type A, flat flange Antenna extender: 100 mm (4"), extension, PTFE gasket: Integrated gasket, only for flat flange process connections, not for antenna options 3-6 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens LUI (Local User Interface) User interface Output and communication signal: PROFIBUS PA approvals: Standard, CE includes European Radio approvals (R&TTE;) 5.8 GHz nominal pressure: According to the pressure/temperature curves of the Service Instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): DN 80 PN 16, Type A, flat faced Antenna Extention: 100 mm (4 inch) extension, PTFE Process Seal/Gasket: Integral Gasket, for FF flange process connections only, not for Antenna options 3,4,5,6 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: PROFIBUS PA Approvals: General Purpose, CE, RED, RCM Pressure rating: rating per pressure/temperature curves in instruction manual

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 40, PN 16 Probe Length: (Lengths from flange face) Standard version, rod 350 mm (13.78") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 40, PN 16 Probe length: (length from flange face) Standard, 350 mm (13.78") rod Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CE, C-TICK, ATEX II 1 G EEx ia IIC T6... T4, ATEX II 1/2 D IP6X T100 C Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP65 Active Shield Length: Standard Length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 40, PN 16 Probe Length: (Lengths from flange face) Standard version, rod 350 mm (13.78") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CE, C-TICK, ATEX II 1 G EEx ia IIC T6...T4, ATEX II 1/2 D I IP6X T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 1" Sealed Slat, 600 lb Probe Length: (length from flange face) Rod extension, length 500 mm (19.69") Process side joints: Graphite Probe material: stainless steel, mat no. 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 1" Sealed Slat, 600 lb Probe Length: (length from flange face) Rod extension, length 500 mm (19.69") Process side joints: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: General purpose (CSA, FM, CE, C-TICK) Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP65 Active Shield length: Extended display - (250 mm thread, 230 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 1" ASME, 600 lb Probe Length: (Lengths from flange face) Extended rod, length 500 mm (19.69") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose (CSA, FM, CE, C-TICK) Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): 6 inch ASME, 300 lb, flat faced Antenna Extention: 100 mm (4 inch) extension, PTFE Process Seal/Gasket: Integral Gasket, for FF flange process connections only, not for Antenna options 3,4,5,6 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Intrinsically Safe, CSA Class I, II, Div 1, Groups A,B,C,D,E,F,G, Industry Canada Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna Material: PTFE Process Connection Flat Flanges (316L Stainless Steel): 6" ASME 300 lb, Flat Flange Antenna Extender: 100 mm (4"), Extension, PTFE Gasket: Integrated Gasket, Only for Flat Flange Process Connections, Not for Antenna Options 3-6 Cable Box/Entry: Epoxy Coated Aluminum, 2 x M20 x 1.5, Siemens User Interface LUI (Local User Interface) communication/output: 4 ... 20 mA, HART, start with <3.6 mA approvals: CSA class I and II Div. I, Group A,B,C,D,G, degree of protection intrinsic safety (IS) with appropriate barrier nominal pressure: According to the pressure/temperature curves of the operating instructions

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: G 1 1/2"(BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Standard version, rod 350 mm (13.78") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: G 1 1/2" (BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe length: (length from flange face) Standard, 350 mm (13.78") rod Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CE, C-TICK, ATEX II 1 G EEx ia IIC T6... T4, ATEX II 1/2 D IP6X T100 C Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP68 Active Shield Length: Standard Length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: G 1 1/2"(BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202 Probe Length: (Lengths from flange face) Standard version, rod 350 mm (13.78") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CE, C-TICK, ATEX II 1 G EEx ia IIC T6...T4, ATEX II 1/2 D I IP6X T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 300 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, Stainless steel, mat no. 1.4404/316L, with: ASME 3" Sealed Slat, 300 lb Probe Length: (length from flange face) Rod extension, length 1000 mm (39.37") Process Side Joints: Graphite Probe Material: Stainless Steel, Mat No. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CE, C-TICK, ATEX II 1 G EEx ia IIC T6... T4, ATEX II 1/2 D IP6X T100 C Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP68 Active Shield length: Extended display - (250 mm thread, 230 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, raised face: 3" ASME, 300 lb Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CE, C-TICK, ATEX II 1 G EEx ia IIC T6...T4, ATEX II 1/2 D I IP6X T100 C Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 25, PN 40 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") .

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, Type A Flat Flange: DN 25, PN 40 Probe Length: (length from flange face) Rod extension, length 750 mm (29.53") Process side joints: Graphite Probe material: Stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: General purpose (CSA, FM) Case and lid: aluminum, epoxy coated, 2 x 1/2" NPT via adapter - Cable entry, IP68 Active Shield length: Standard length - (125 mm thread, 105 mm flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 25, PN 40 Probe Length: (Lengths from flange face) Extended rod, length 750 mm (29.53") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: General Purpose (CSA, FM) Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Standard length - (125 mm threaded, 105 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 80, PN 16 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 80, PN 16 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x 1/2" NPT via Adapter - Cable Entry, IP68 Active Shield Length: Extended Display - (250 mm Thread, 230 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 80, PN 16 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x 1/2" NPT via adapter - cable inlet, IP68 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

Pointek CLS300 RF Capacitance point level switch, digital, high temperature design. Detects level and interface in aggressive liquids, solids, slurries, and foam. Adjustable, 1 m (3.28 ft), insertion, adaptable sensitivity, with active shield to tune out build-up on probe. With display and digital communications. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 100, PN 16 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/ FM Class I, II, III Div. 1 Gr. A, B, C, D, E, F, G T4 or T6 Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.

. Pointek CLS300 RF Capacitive Level Switch, Digital, High Temperature Variant. Level and level/interface detection of aggressive liquids, solids, slurries and foam. Insertion length 1 m (3.28 ft) adjustable, sensitivity adjustable, with Active Shield technology to ignore buildup in the probe. With digital indication and communication module. Process connection: Welded flange, stainless steel, mat no. 1.4404/316L, flat flange type A: DN 100, PN 16 Probe length: (length from flange face) Rod extension, length 1000 mm (39.37") Process side seals: Graphite Probe material: stainless steel, mat no. 1.4404/316L with ceramic insulators Approvals: Intrinsic safety CSA/FM Class I, Div. 1, Tam. A, B, C, D, CSA/FM Class II, Div. 1, tam. E, F, G, CSA/FM Class III T4 Case & Lid: Aluminum, Epoxy Coated, 2 x M20 x 1.5 Cable Entry, IP65 Active Shield Length: Extended Display - (250 mm Thread, 230 mm Flange)

Pointek CLS300 - Digital - High Temp Version with Threaded or Flanged process connection: Inverse frequency shift capacitance level switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam and interfaces in demanding conditions where high pressure and temperatures are present. Process Connection: Welded flange, 316L stainless steel, Type A flat faced: DN 100, PN 16 Probe Length: (Lengths from flange face) Extended rod, length 1000 mm (39.37") . Wetted Seals: Graphite Probe Material: 316L Stainless Steel with Ceramic Isolators Approvals: Intrinsically Safe CSA/FM Class I, Div. 1, Gr. A, B, C, D, CSA/FM Class II, Div. 1, Gr. E, F, G, CSA/FM Class III T4 Enclosure and Lid: Aluminum epoxy coated 2 x M20 x 1.5 cable inlet, IP65 Active Shield Length: Extended Shield - (250 mm threaded, 230 mm flanged)

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): JIS DN 100 10K Antenna Extention: 100 mm (4 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Flame Proof: ATEX II 1/2G Ex db mb ia IIC T4 Ga/Gb; UKEX II 1/2G Ex db mb ia IIC T4 Ga/Gb; CE, UKCA, RED, RCM, EAC Pressure rating: rating per pressure/temperature curves in instruction manual

SITRANS LR200 PTFE Rod Radar Level Transmitter - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries. Antenna material: PTFE Process connection Flat flanges (316L stainless steel): JIS DN100 10K Antenna extender: 100 mm (4"), extension, stainless steel screen 1.4404/316L gasket: FKM O-ring, not available for Flat flange combined with antenna options 0, 1, 2 Cable box/entry: Epoxy coated aluminum, 2 x M20 x 1.5, Siemens User Interface LUI (Local User Interface) communication/output: 4 ... 20 mA, HART, start with <3.6 mA approvals: ATEX II 1/2 G EEx em ia IIC T4, no nominal pressure barrier required: According to the pressure/temperature curves in the operating instructions

SITRANS LR200 Radar level transmitter with PTFE rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Antenna material: PTFE Process Connection Flat faced flanges (316L stainless steel): JIS DN 100 10K Antenna Extention: 100 mm (4 inch) extension, 316 stainless steel shield Process Seal/Gasket: FKM O-ring, not available for FF flanges with Antenna options 0,1,2 Enclosure/Cable inlet: Aluminium, Epoxy paint, 2 x M20 x1.5 Communication/Output: 4-20mA HART, start-up at <3.6mA Approvals: Flame Proof, ATEX II 1/2G Ex dmbia IIC T4 Ga/Gb, CE, RED, RCM; GOST-R Pressure rating: rating per pressure/temperature curves in instruction manual