SIEMENS

SIPART PS2 smart electropneumatic positioner for pneumatic linear and part-turn actuators; 2-,3-,4-wire; 4...20mA; double acting; Enclosure stainless steel, flame-proof . Type of explosion protection: Explosion proof Connection thread M25 x 1,5 / G 1/4 (only for EEx d explosion protection) Digital I/O Module (DIO) Optionally available with device plug M12 (D coding) Order code: -Z D55 without option module . Instruction manual: French, Spanish, Italian . with mounted pressure gauge made of plastic, IP31, aluminum block, 1/4" NPT aluminum block, 1/4" NPT

SIPART PS2 Intelligent electro-pneumatic position regulator, 4...20mA (3/4 wires), nEx, double acting, stainless steel case, explosion-proof (Ex d), for linear pneumatic actuators and fraction turn. Standard Protection Mode (Ex): Explosion-proof enclosure (Ex d), Dust-proof protection by enclosure (Ex t). Connection thread on.: M25x1.5 / pneu.: G 1/4 Digital I/O Module (DIO), 1 digital input, 3 digital outputs (2 min. or max. limit values, 1 fault warning output) No option module. . Short instructions Spanish / French / Italian. Standard / Fail-Safe - Purge actuator in case of auxiliary power failure (single effect only). Double-acting 1/4-18 NPT aluminum gauge block with IP31 plastic pressure gauge (MPa, psi)

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: European design with ceramic socket Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.1 -40 ... 750Cel Length unit of med. (mm): B = 451 ... 500 Initial: 500 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: European design with ceramic socket Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.1 -40 ... 750Cel Length unit of med. (mm): B = 451 ... 500 Initial: 500 Non-Ex Requirements for EU/Australia

MultiRanger 200 Ultrasonic level controller: continuous, non-contact, 15 m (50 ft) range. Monitors level, volume, and open channel flow in liquids, slurries, and solids. Versions: MultiRanger 100, level measurement Mounting, enclosure design: Panel Mount (CE, CSA US/C , FM, UL) Input voltage: 12 to 30 VDC Number of measurement points: Dual point version Data Communications (Smartlinx): Smartlinx PROFIBUS DPVO module Output relays: 6 relays (4 Form A, 2 Form C), 250 V AC Approvals: General Purpose, CE, FM,CSA US/C,UL, listed, RCM,EAC,KCC

MultiRanger 100/200 Ultrasonic Level Controller: Continuous, non-contact measurement, range 15 m (50 ft). It monitors the level, volume, and flow in open channel of liquids, sludge, and solids. Versions: MultiRanger 100 only for level measurement Mounting, box design: Panel mounting (CE, UKCA, CCSAUS, FM, UL) Product is in phase out but still available to order, Consider replacing with 7ML5033-xF Input voltage: 12 ... 30 V DC Number of measurement points: Two-point version Data communication (SmartLinx): SmartLinx PROFIBUS DPV0 module Output relays: 6 relays (4 A-contacts, 2 C-contacts), 250 V AC Approvals: Ordinary Locations/ Non-Ex, CE, UKCA, FM,CCSAUS, UL Listed, RCM, EAC, KC

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral-insulated design Probe diameter: 6 mm Connection side: European design with free wire ends for converter mounting Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 85 ... 100 Initial: 100 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral-insulated design Probe diameter: 6 mm Connection side: European design with free wire ends for converter mounting Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 85 ... 100 Initial: 100 Non-Ex Requirements for EU/Australia

SITRANS LR200 Radar level transmitter with polypropylene rod: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries. Enclosure / Cable Inlet: Aluminum, Epoxy painted, 2 X 1/2 " NPT Polypropylene antenna type - (Max. 3 Bar pressure and +80'C): R 1-1/2 inch ((BSPT), EN 10226-1) comes with integral 100 mm shield Approvals: Non incendive, FM Class I, Div 2, Gr. A,B,C,D, FCC Communication / Output: 4-20mA HART, start-up at <3.6mA .

. SITRANS LR200 Radar Level Transmitter with Polypropylene Rod - Continuous, non-contact, 20 m (66 ft) range measurement for liquids and sludge. Field box / cable entry: Epoxy coated aluminium, 2 X 1/2 " NPT Polypropylene antenna (Max. pressure 3 bar and +80 C): R 1-1/2 inches ((BSPT) EN 10226-1), with integrated 100 mm shielding Approvals: Electrical material for zone 2 (non-flammable) FM, Class I, Div. 2, Tam. A,B,C,D, FCC, communication/output: 4 ... 20 mA, HART, <3.6 mA start

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: amer design. (nozzle damping) Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 601 ... 700 Initial: 655 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: amer design. (nozzle damping) Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 601 ... 700 Initial: 655 Non-Ex Requirements for EU/Australia

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 3" (80 mm) Antenna: 3" horn antenna, fits 80 mm or 3" nozzles Purge (Self Cleaning) Connection: No Purge connection . Output/Communication: 4 to 20 mA, HART Power Supply/Cable Inlet: 100 to 230 V AC, 2 x NPT x 1.5 Approvals: CSA/FM Class II, Div.1, Gr. E,F,G Class III .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 3" / 80 mm antenna: 3" horn antenna, suitable for 80 mm (3") mm Purge connection (self-cleaning): No purge connection Output/communication: 4 ... 20 mA, HART Auxiliary power/cable entry: AC 100 ... 230 V, 2 x 1/2" NPT Approvals: CSA/FM Class II, Div. 1, Groups E, F and G Class III

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with ceramic socket Average range: -200 to 600Cel; Sensor quantity, type, accuracy 2xPt100, Cl.A -100 ... 450Cel; Extended measuring range Length unit of med. (mm): B = 801 ... 900 Initial: 825 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with ceramic socket Average range: -200 to 600Cel; Sensor quantity, type, accuracy 2xPt100, Cl.A -100 ... 450Cel; Extended measuring range Length unit of med. (mm): B = 801 ... 900 Initial: 825 Non-Ex Requirements for EU/Australia

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 4" (100 mm) Antenna: 3" horn antenna, fits 80 mm or 3" nozzles with 200 mm extension Purge (Self Cleaning) Connection: Purge Connection . Output/Communication: PROFIBUS PA Power Supply/Cable Inlet: 24 V DC, 2 x M20 x 1.5 Approvals: General Purpose, CSA US/C, Industry Canada,FCC,CE, RED .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 4" / 100 mm antenna: 3" horn antenna, suitable for 80 mm (3") nozzle with 200 mm extension Purge connection (self-cleaning): Purge connection Output/communication: PROFIBUS PA Auxiliary power/cable entry: DC 24 V, 2 x M20 x 1.5 approvals: General Purpose, CSAUS/C, Industry Canada, FCC, CE and R

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 4" (100 mm) Antenna: 4" horn antenna, fits 100 mm or 4" nozzles Purge (Self Cleaning) Connection: Purge Connection . Output/Communication: PROFIBUS PA Power Supply/Cable Inlet: 100 to 230 V AC, 2 x M20 x 1.5 Approvals: General Purpose, CSA US/C, Industry Canada,FCC,CE, RED .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 4" / 100 mm antenna: 4" Horn antenna, suitable for 100 mm (4") mm Purge connection (self-cleaning): Purge connection Output/communication: PROFIBUS PA Auxiliary power/cable input: AC 100 ... 230 V, 2 x M20 x 1.5 Approvals: General Purpose, CSAUS/C, Industry Canada, FCC, CE and R

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 85 ... 100 Initial: 100 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 85 ... 100 Initial: 100 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -200 to 600Cel; Sensor quantity, type, accuracy 1xPt100, Cl.B -196 ... 600Cel; Extended measuring range Length unit of med. (mm): B = 551 ... 600 Initial: 555 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -200 to 600Cel; Sensor quantity, type, accuracy 1xPt100, Cl.B -196 ... 600Cel; Extended measuring range Length unit of med. (mm): B = 551 ... 600 Initial: 555 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor quantity, type, accuracy 2xPt1000, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 351 ... 400 Initial: 375 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor quantity, type, accuracy 2xPt1000, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 351 ... 400 Initial: 375 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measure for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt100, Cl.A -30 ... 300Cel; Increased resistance to vibrations Length unit of med. (mm): B = 301 ... 350 Initial: 315 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measure for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt100, Cl.A -30 ... 300Cel; Increased resistance Length unit of med. (mm): B = 301 ... 350 Initial: 315 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection Side: European Design with Ceramic Socket Average Range: -40 to 1000Cel; Sensor Qty, Type, Accuracy 2xTC K, Cl.2 -40 ... 1000Cel Length unit of med. (mm): B = 1501 ... 2000 Initial:1700 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection Side: European Design with Ceramic Socket Average Range: -40 to 1000Cel; Sensor Qty, Type, Accuracy 2xTC K, Cl.2 -40 ... 1000Cel Length unit of med. (mm): B = 1501 ... 2000 Initial: 1700 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor quantity, type, accuracy 2xPt100, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 85 ... 100 Initial: 100 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor quantity, type, accuracy 2xPt100, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 85 ... 100 Initial: 100 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.AA 0 ... 150Cel; Increased resistance to vibrations Length unit of med. (mm): B = 251 ... 300 Initial: 275 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.AA 0 ... 150Cel; Increased resistance Length unit of med. (mm): B = 251 ... 300 Initial: 275 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt1000, Cl.A -30 ... 300Cel; Increased resistance to vibrations Length unit of med. (mm): B = 401 ... 450 Initial: 405 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt1000, Cl.A -30 ... 300Cel; Increased resistance Length unit of med. (mm): B = 401 ... 450 Initial: 405 Non-Ex Requirements for EU/Australia

SITRANS LVL100 Vibrating point level switch. Detects level and material in liquids and slurries. Compact, with 40 mm (1.6 inch) insertion. Approvals: Overfill protection (WHG) Process temperature: Hygienic applications -40 to 150 C Process connection: Tri-Clamp 2" PN16 / 316L Ra<0.8 Micrometer Electronics: Transistor output PNP 10...55 V DC Housing: 316L Electrical connection / Protection: M12x1 / IP67 1 . .

. SITRANS LVL100 Vibratory Level Switch. Detects the . level of liquid materials and sludge. Compact, with insertion length 40 mm (1.6 inch). Approvals: Overflow safety according to WHG process temperature: Sanitary applications -40 ... 150 C process connection: Tri-Clamp 2" PN16/316L Ra <0.8 microns electronics: PNP DC transistor output 10...55 V Box: 316L Electrical connection/ degree of protection: M12x1 / IP67

SITRANS LVL100 Vibrating point level switch. Detects level and material in liquids and slurries. Compact, with 40 mm (1.6 inch) insertion. Approvals: Shipping approvals Process temperature: Extended -40 to 150 C Process connection: Thread G1" A PN64 / 316L Electronics: Transistor output PNP 10...55 V DC Housing: 316L Electrical connection / Protection: Acc. to DIN43650 incl. plug with QuickOn connection / IP65 . .

. SITRANS LVL100 Vibratory Level Switch. Detects the . level of liquid materials and sludge. Compact, with insertion length 40 mm (1.6 inch). Approvals: Marine Approvals Process temperature: Advanced -40 ... 150 C process connection: Thread G1" A PN64/316L electronics: Transistor output PNP DC 10...55 V Box: 316L Electrical connection/ degree of protection: According to DIN 43650 incl. connector with QUICKON quick connection / IP65

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 6" (150 mm) Antenna: 4" horn antenna, fits 100 mm or 4" nozzles with 100 mm extension Purge (Self Cleaning) Connection: No Purge connection . Output/Communication: PROFIBUS PA Power Supply/Cable Inlet: 100 to 230 V AC, 2 x NPT x 1.5 Approvals: General Purpose, CSA US/C, Industry Canada,FCC,CE, RED .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 6" / 150 mm antenna: 4" Horn antenna, suitable for 100 mm (4") nozzle with 100 mm extension Purge connection (self-cleaning): Without purge connection Output/communication: PROFIBUS PA Auxiliary power/cable entry: AC 100 ... 230 V, 2 x 1/2" NPT Approvals: General Purpose, CSAUS/C, Industry Canada, FCC, CE and R

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: European design with ceramic socket Average range: -40 to 1000Cel; Sensor Qty, Type, Accuracy 2xTC N, Cl.1 -40 ... 1000Cel Length unit of med. (mm): B = 601 ... 700 Initial: 655 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 6 mm Connection Side: European Design with Ceramic Socket Average Range: -40 to 1100Cel; Sensor Qty, Type, Accuracy 2xTC N, Cl.1 -40 ... 1000Cel Length unit of med. (mm): B = 601 ... 700 Initial: 655 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor quantity, type, accuracy 1xPt1000, Cl.B -50 ... 400Cel; Increased resistance to vibrations Length unit of med. (mm): B = 1001 ... 1500 Initial:1250 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor quantity, type, accuracy 1xPt1000, Cl.B -50 ... 400Cel; Increased resistance Length unit of med. (mm): B = 1001 ... 1500 Initial: 1250 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt100, Cl.A -30 ... 300Cel; Increased resistance to vibrations Length unit of med. (mm): B = 601 ... 700 Initial: 655 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt100, Cl.A -30 ... 300Cel; Increased resistance Length unit of med. (mm): B = 601 ... 700 Initial: 655 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.A -30 ... 300Cel; Increased resistance to vibrations Length unit of med. (mm): B = 101 ... 150 Initial: 145 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.A -30 ... 300Cel; Increased resistance Length unit of med. (mm): B = 101 ... 150 Initial: 145 Non-Ex Requirements for EU/Australia

SITRANS LR250 Radar level transmitter with encapsulated horn and PTFE lens: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries in the chemical industry. Process Connection Material:Stainless steel 1.4404/1.4435 Flanged Process Connection Types (Stainless steel 1.4404/1.4435): DN100 PN10/16 EN 1092-1 type B1 raised face Communication: 4...20mA HART,start-up at <3.6mA - Enclosure (with Cable inlets): Aluminum, 2 X M20 x 1.5 Antenna Lens Material: TFM 1600 Flush lens Approvals: Non-incendive: CSA/FM Class I, Div. 2, Groups A, B, C, D T5, FCC, Industry Canada Pressure Rating: Rating per pressure/ temperature curves in instruction manual

SITRANS LR250 Radar Level Transmitter with Encapsulated Horn Antenna and PTFE Lens: Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries in chemical industry applications. Material, process connection: Stainless steel 1.4404/1.4435 Types of flanged process connection (stainless steel 1.4404/1.4435): DN100 PN10/16 EN 1092-1 type B1 with protrusion Communications: 4...20mA HART, start at <3.6mA - Box (with cable entry): Aluminum, 2 X M20 x 1.5 Lens material (antenna): TFM 1600 recessed lens Approvals: Non-incendiary: CSA/FM Class I, Div. 2, Groups A,B, C, D T5, FCC, Industry Canada Pressure: See pressure/temperature reduction curves in the service instructions

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.A -30 ... 300Cel; Increased resistance to vibrations Length unit of med. (mm): Standard: B = 585 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.A -30 ... 300Cel; Increased resistance Length unit of med. (mm): Standard: B=585 Non-Ex Requirements for EU/Australia

Weigh deck 600, 304 SS construction with UHMW Polyethelene sliders, load cells are available in nickle pl., or stainless steel. Two calibration weights are required and ordered as separate item. Refer to optional equipment. Belt Width: 30" (750mm) Load cell capacity: 15 kg nickel plated . .

. Milltronics WD600 Belt Scale: Accuracy ± 0.5 ... 1% . of the total weight, measuring range 25 ... 100%, capacity up to 100 t/h (110 STPH). Belt Width: 30" (750mm) Load Cell Capacity: 15kg Nickel-Plated

MultiRanger 200 Ultrasonic level controller: continuous, non-contact, 15 m (50 ft) range. Monitors level, volume, and open channel flow in liquids, slurries, and solids. Versions: MultiRanger 100, level measurement Mounting, enclosure design: Wall mount, standard enclosure Input voltage: 100 to 230 VAC Number of measurement points: Dual point version Data Communications (Smartlinx): Smartlinx Devicenet module Output relays: 3 relays (2 Form A, 1 Form C), 250 V AC Approvals: CSA Class I, Div.2, Group A,B,C and D; Class II, Div.2, Group F and G; Class III

MultiRanger 100/200 Ultrasonic Level Controller: Continuous, non-contact measurement, range 15 m (50 ft). It monitors the level, volume, and flow in open channel of liquids, sludge, and solids. Versions: MultiRanger 100 only for level measurement Mounting, box design: Standard box for wall mounting Product is in phase out but still available to order, Consider replacing with 7ML5033-xD Input voltage: 100 ... 230 V AC Number of Measurement Points : Two-Point Version Data Communication (SmartLinx): SmartLinx DeviceNet Module Output Relays: 3 Relays (2 A-Contacts, 1 C Contact), 250 V AC Approvals: CSA Class I, Div. 2, Groups A, B, C, and D; Class II, Div. 2, Groups F and G; Class III

MultiRanger 200 Ultrasonic level controller: continuous, non-contact, 15 m (50 ft) range. Monitors level, volume, and open channel flow in liquids, slurries, and solids. Versions: MultiRanger 200, level, volume, flow and differential measurements Mounting, enclosure design: 4 button HMI, Wall mount, standard enclosure Input voltage: 100 to 230 VAC Number of measurement points: Dual point version Data Communications (Smartlinx): Smartlinx PROFIBUS DPV1 module Output relays: 6 relays (4 Form A, 2 Form C), 250 V AC Approvals: CSA Class I, Div.2, Group A,B,C and D; Class II, Div.2, Group F and G; Class III

MultiRanger 100/200 Ultrasonic Level Controller: Continuous, non-contact measurement, range 15 m (50 ft). It monitors the level, volume, and flow in open channel of liquids, sludge, and solids. Versions: MultiRanger 200 for level, volume, flow and differential level measurement Mounting, enclosure design: HMI interface with 4 buttons, standard housing for wall mounting Input voltage: 100 ... 230 V AC Number of measurement points: Two-point version Data communication (SmartLinx): SmartLinx PROFIBUS DPV1 module Output relays: 6 relays (4 A-contacts, 2 C contacts), 250 V AC Approvals: CSA Class I, Div. 2, Groups A, B, C, and D; Class II, Div. 2, Groups F and G; Class III

MultiRanger 200 Ultrasonic level controller: continuous, non-contact, 15 m (50 ft) range. Monitors level, volume, and open channel flow in liquids, slurries, and solids. Versions: MultiRanger 200, level, volume, flow and differential measurements Mounting, enclosure design: 4 button HMI, Wall mount, 4 entries, 4 M20 cable glands included Input voltage: 12 to 30 VDC Number of measurement points: Dual point version Data Communications (Smartlinx): Smartlinx Devicenet module Output relays: 6 relays (4 Form A, 2 Form C), 250 V AC Approvals: CSA Class I, Div.2, Group A,B,C and D; Class II, Div.2, Group F and G; Class III

MultiRanger 100/200 Ultrasonic Level Controller: Continuous, non-contact measurement, range 15 m (50 ft). It monitors the level, volume, and flow in open channel of liquids, sludge, and solids. Versions: MultiRanger 200 for level, volume, flow and differential level measurement Mounting, enclosure design: HMI interface with 4 buttons, wall mounting, 4 holes, 4 M20 cable glands included Input voltage: 12 ... 30 V DC Number of Measurement Points: Two-Point Version Data Communication (SmartLinx): SmartLinx DeviceNet Module Output Relays: 6 Relays (4 A-Contacts, 2 C-Contacts), 250 V AC Approvals: CSA Class I, Div. 2, Groups A, B, C, and D; Class II, Div. 2, Groups F and G; Class III

Siemens HydroRanger 200 Ultrasonic level controller for up to six pumps that provides control, differential control and open channel flow monitoring. Mounting: Panel mount Input voltage: 12 to 30 VDC Number of measurement points: Single point version, level only, 3 relays Data Communications: Smartlinx PROFIBUS DP V0 module Approvals: General Purpose CE, FM, CSA US/C , UL listed, RCM, EAC, KCC

HydroRanger 200 Ultrasonic Level Controller: Continuous, non-contact measurement, range 15 m (50 ft). It monitors the level, volume, and flow in open channel of liquids, sludge, and solids. Mounting: Recessed panel mounting Auxiliary power: DC, 12 to 30 V Number of measuring points: single-channel version; level only; 3 Data Communication Relays (SmartLinx): SmartLinx PROFIBUS DPV0 Module Approvals: Ordinary Locations/General Purpose (Non-Ex), CE, UKCA, FM, CCSAUS, UL Listed, RCM, EAC, KC

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 3" (80 mm) Antenna: 3" horn antenna, fits 80 mm or 3" nozzles with 200 mm extension Purge (Self Cleaning) Connection: Purge Connection . Output/Communication: PROFIBUS PA Power Supply/Cable Inlet: 24 V DC, 2 x M20 x 1.5 Approvals: ATEX II 1/2 D T6, CE, RED .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 3" / 80 mm antenna: 3" horn antenna, suitable for 80 mm (3") nozzle with 200 mm extension Purge connection (self-cleaning): Purge connection Output/communication: PROFIBUS PA Auxiliary power/cable entry: DC 24 V, 2 x M20 x 1.5 approvals: ATEX II 1/2 D T6, CE, R

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.AA 0 ... 150Cel; Basic version Length unit of med. (mm): Standard: B = 345 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt1000, Cl.AA 0 ... 150Cel; Basic version Length unit of med. (mm): Standard: B=345 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor quantity, type, accuracy 2xPt100, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 801 ... 900 Initial: 825 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor quantity, type, accuracy 2xPt100, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 801 ... 900 Initial: 825 Non-Ex Requirements for EU/Australia

SITRANS LVL100 Vibrating point level switch. Detects level and material in liquids and slurries. Compact, with 40 mm (1.6 inch) insertion. Approvals: Shipping approvals Process temperature: Standard -40 to 100 C Process connection: Thread 3/4" NPT PN64 / 316L Electronics: Transistor output PNP 10...55 V DC Housing: 316L Electrical connection / Protection: M12x1 / IP67 1 . .

. SITRANS LVL100 Vibratory Level Switch. Detects the . level of liquid materials and sludge. Compact, with insertion length 40 mm (1.6 inch). Approvals: Marine approvals Process temperature: Standard -40 ... 100 C process connection: 3/4" NPT PN64/316L thread electronics: PNP DC transistor output 10...55 V Box: 316L Electrical connection/ degree of protection: M12x1 / IP67

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 6" (150 mm) Antenna: 3" horn antenna, fits 80 mm or 3" nozzles with 100 mm extension Purge (Self Cleaning) Connection: No Purge connection . Output/Communication: 4 to 20 mA, HART Power Supply/Cable Inlet: 100 to 230 V AC, 2 x M20 x 1.5 Approvals: CSA/FM Class II, Div.1, Gr. E,F,G Class III .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 6" / 150 mm antenna: 3" horn antenna, suitable for 80 mm (3") mm with 100 mm extension Purge connection (self-cleaning): Without purge connection Output/communication: 4 ... 20 mA, HART Auxiliary power/cable entry: AC 100 ... 230 V, 2 x M20 x 1.5 approvals: CSA/FM Class II, Div. 1, Groups E, F and G Class III

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with ceramic socket Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt100, Cl.A -30 ... 300Cel; Basic version Length unit of med. (mm): B = 85 ... 100 Initial: 100 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with ceramic socket Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 2xPt100, Cl.A -30 ... 300Cel; Basic version Length unit of med. (mm): B = 85 ... 100 Initial: 100 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with ceramic socket Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 401 ... 450 Initial: 405 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with ceramic socket Average range: -40 to 750Cel; Sensor Qty, Type, Accuracy 2xTC J, Cl.2 -40 ... 750Cel Length unit of med. (mm): B = 401 ... 450 Initial: 405 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt100, Cl.A -30 ... 300Cel; Increased resistance to vibrations Length unit of med. (mm): B = 601 ... 700 Initial: 655 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt100, Cl.A -30 ... 300Cel; Increased resistance Length unit of med. (mm): B = 601 ... 700 Initial: 655 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor quantity, type, accuracy 1xPt1000, Cl.AA 0 ... 150Cel; Basic version Length unit of med. (mm): Standard: B = 585 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for converter mounting Average range: -50 to 400Cel; Sensor quantity, type, accuracy 1xPt1000, Cl.AA 0 ... 150Cel; Basic version Length unit of med. (mm): Standard: B=585 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: European design with ceramic socket Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt100, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 251 ... 300 Initial: 275 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 6 mm Connection side: European design with ceramic socket Average range: -50 to 400Cel; Sensor Qty, Type, Accuracy 1xPt100, Cl.B -50 ... 400Cel; Basic version Length unit of med. (mm): B = 251 ... 300 Initial: 275 Non-Ex Requirements for EU/Australia

SITRANS LR250 Radar level transmitter with encapsulated horn and PTFE lens: continuous, non-contact, 20 m (66 ft) range, for liquids and slurries in the chemical industry. Process Connection Material:Stainless steel 1.4404/1.4435 Flanged Process Connection Types (Stainless steel 1.4404/1.4435): 150A 10K JIS B 2220 raised face Communication: 4...20mA HART,start-up at <3.6mA - Enclosure (with Cable Inlets):Aluminum, 2 X 1/2" NPT Antenna Lens Material: TFM 1600 Flush lens Approvals: Non Sparking: ATEX II 3G Ex nA IIC T4 Gc, CE RED, RCM Pressure Rating: Rating per pressure/ temperature curves in instruction manual

SITRANS LR250 Radar Level Transmitter with Encapsulated Horn Antenna and PTFE Lens: Continuous, non-contact, 20 m (66 ft) range measurement for liquids and slurries in chemical industry applications. Material, process connection: Stainless steel 1.4404/1.4435 Flanged process connection types (stainless steel 1.4404/1.4435): 150A 10K JIS B 2220 with highlight Communications: 4...20mA HART, start at <3.6mA - Box (with cable entry): Aluminum, 2 X 1/2" NPT Lens material (antenna): TFM 1600 recessed lens Approvals: Increased Safety / Non Sparking: ATEX II 3G Ex ec IIC T4 Gc; UKEX II 3G Ex ec IIC T4 Gc; EAC Ex 2Ex nA IIC T4 Gc X; CE, UKCA, RED, RCM Pressure: See pressure/temperature reduction curves in the operating instructions

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -40 to 1000Cel; Sensor Qty, Type, Accuracy 2xTC K, Cl.2 -40 ... 1000Cel Length unit of med. (mm): B = 501 ... 550 Initial: 525 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of Measurement for SITRANS TS500, Mineral Insulated Design Probe Diameter: 8 mm (6 mm Cable Diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -40 to 1000Cel; Sensor Qty, Type, Accuracy 2xTC K, Cl.2 -40 ... 1000Cel Length unit of med. (mm): B = 501 ... 550 Initial: 525 Non-Ex Requirements for EU/Australia

MultiRanger 200 Ultrasonic level controller: continuous, non-contact, 15 m (50 ft) range. Monitors level, volume, and open channel flow in liquids, slurries, and solids. Versions: MultiRanger 200, level, volume, flow and differential measurements Mounting, enclosure design: Wall mount, standard enclosure Input voltage: 100 to 230 VAC Number of measurement points: Single point version Data Communications (Smartlinx): Without module Output relays: 3 relays (2 Form A, 1 Form C), 250 V AC Approvals: CSA Class I, Div.2, Group A,B,C and D; Class II, Div.2, Group F and G; Class III

MultiRanger 100/200 Ultrasonic Level Controller: Continuous, non-contact measurement, range 15 m (50 ft). It monitors the level, volume, and flow in open channel of liquids, sludge, and solids. Versions: MultiRanger 200 for level, volume, flow and differential level measurement Mounting, enclosure design: Standard box for wall mounting Product is in phase out but still available to order, Consider replacing with 7ML5033-xD Input voltage: 100 ... 230 V AC Number of measurement points: Version for one point Data communication (SmartLinx): Without module Output relays: 3 relays (2 contacts A, 1 contact C), 250 V AC Approvals: CSA Class I, Div. 2, Groups A, B, C, and D; Class II, Div. 2, Groups F and G; Class III

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 3" (80 mm) Antenna: 3" horn antenna, fits 80 mm or 3" nozzles with 500 mm extension Purge (Self Cleaning) Connection: No Purge connection . Output/Communication: PROFIBUS PA Power Supply/Cable Inlet: 24 V DC, 2 x NPT x 1.5 Approvals: General Purpose, CSA US/C, Industry Canada,FCC,CE, RED .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 3" / 80 mm antenna: 3" horn antenna, suitable for 80 mm (3") nozzle with 500 mm extension Purge connection (self-cleaning): Without purge connection Output/communication: PROFIBUS PA Auxiliary power/cable entry: DC 24 V, 2 x 1/2" NPT Approvals: General Purpose, CSAUS/C, Industry Canada, FCC, CE and R

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 4" (100 mm) Antenna: 3" horn antenna, fits 80 mm or 3" nozzles Purge (Self Cleaning) Connection: Purge Connection . Output/Communication: 4 to 20 mA, HART Power Supply/Cable Inlet: 100 to 230 V AC, 2 x NPT x 1.5 Approvals: CSA/FM Class II, Div.1, Gr. E,F,G Class III .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 4" / 100 mm antenna: 3" horn antenna, suitable for 80 mm (3") mm Purge connection (self-cleaning): Purge connection Output/communication: 4 ... 20 mA, HART Auxiliary power/cable entry: AC 100 ... 230 V, 2 x 1/2" NPT Approvals: CSA/FM Class II, Div. 1, Groups E, F and G Class III

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for mounting converters Average range: -40 to 1000Cel; Sensor Qty, Type, Accuracy 1xTC K, Cl.2 -40 ... 1000Cel Length unit of med. (mm): B = 551 ... 600 Initial: 555 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: European design with free wire ends for mounting converters Average range: -40 to 1000Cel; Sensor Qty, Type, Accuracy 1xTC K, Cl.2 -40 ... 1000Cel Length unit of med. (mm): B = 551 ... 600 Initial: 555 Non-Ex Requirements for EU/Australia

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor quantity, type, accuracy 1xPt100, Cl.AA 0 ... 150Cel; Increased resistance to vibrations Length unit of med. (mm): B = 901 ... 1000 Initial: 950 Prot. c. expl. (ATEX,IECEx) For EU/Australia Non-Ex Requirements

SITRANS TSinsert Unit of measurement for SITRANS TS500, mineral insulated design Probe diameter: 10 mm (6 mm cable diameter) Please note: Unit of measurement not replaceable. Connection side: amer design. (nozzle damping) Average range: -50 to 400Cel; Sensor quantity, type, accuracy 1xPt100, Cl.AA 0 ... 150Cel; Increased resistance Length unit of med. (mm): B = 901 ... 1000 Initial: 950 Non-Ex Requirements for EU/Australia

Sitrans LR 460: 4-wire, 24 GHz FMCW radar level transmitter for continuous monitoring of solids in silos to a range of 100 m (328 ft). Ideal for applications with extreme dust and high temperatures to 200 Cel. (392 F). Order hand programmer separately! . Process connection: Universal, flat faced, 0.5 bar (7.25 psi) maximum with integral Easy Aimer ball: 4" (100 mm) Antenna: 4" horn antenna, fits 100 mm or 4" nozzles with 100 mm extension Purge (Self Cleaning) Connection: Purge Connection . Output/Communication: 4 to 20 mA, HART Power Supply/Cable Inlet: 24 V DC, 2 x NPT x 1.5 Approvals: CSA/FM Class II, Div.1, Gr. E,F,G Class III .

. SITRANS LR460 Radar level transmitter with antenna . Horn: Continuous, non-contact measurement, range 100 m (328 ft), . for tough applications with solids. Process connection: Universal flat flange, 0.5 bar (7.25 psi) maximum with integrated adjustable flange Type EA: 4" / 100 mm antenna: 4" Horn antenna, suitable for 100 mm (4") nozzle with 100 mm extension Purge connection (self-cleaning): Purge connection Output/communication: 4 ... 20 mA, HART Auxiliary power/cable entry: DC 24 V, 2 x 1/2" NPT Approvals: CSA/FM Class II, Div. 1, Groups E, F and G Class III