Produto adicionado com sucesso ao seu carrinho de compras
PLC-RPT- 60DC/21HC
2900295
PHOENIX_CONTACT
10
PLC-INTERFACE para altas correntes contínuas, que consiste em bloco de terminais básico PLC-BPT ... / 21 de HC com o push-em conexão e retransmissão miniatura pluggable para a montagem ferroviário NS 35 / 7,5, limitação de corrente contínua de até 10 A comutada 1 contato, tensão de entrada 60 V DC
Interface
* Produto novo em sua embalagem original com todas as garantias e certificações de PHOENIX_CONTACT
Obrigado pelo seu interesse nos nossos artigos, esperamos que o prazo indicado seja conveniente para si.
Durante a preparação do pedido pode seleccionar o tipo de envío que melhor se adapte ás suas necessidades: Aéreo Express 24Hrs, Terrestre Standard 48/72Hrs, etc.
Width | 14 mm |
---|---|
Height | 80 mm |
Depth | 94 mm |
Ambient temperature (operation) | -40 °C ... 60 °C |
---|---|
Ambient temperature (storage/transport) | -40 °C ... 85 °C |
Nominal input voltage UN | 60 V DC |
---|---|
Typical input current at UN | 10 mA |
Typical response time | 8 ms |
Typical release time | 10 ms |
Protective circuit | Protection against polarity reversal Polarity protection diode |
Free-wheeling diode Damping diode | |
Operating voltage display | Yellow LED |
Power dissipation for nominal condition | 0.6 W |
Contact type | 1 PDT |
---|---|
Contact material | AgNi |
Maximum switching voltage | 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...) |
Minimum switching voltage | 12 V (at 10 mA) |
Min. switching current | 10 mA (at 12 V) |
Maximum inrush current | 30 A (300 ms) |
Limiting continuous current | 10 A |
6 A (value applies to connections 12. If connections 12 are bridged, the normal value applies.) | |
Interrupting rating (ohmic load) max. | 240 W (at 24 V DC) |
58 W (at 48 V DC) | |
48 W (at 60 V DC) | |
50 W (at 110 V DC) | |
80 W (at 220 V DC) | |
2500 VA (for 250 V AC) | |
Interrupting rating (ohmic load) max. bridged | 144 W (for 24 V DC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.) |
1500 VA (for 250 V AC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.) | |
Switching capacity in acc. with DIN VDE 0660/IEC 60947 | 2 A (at 24 V, DC13) |
0.2 A (at 110 V, DC13) | |
0.2 A (at 250 V, DC13) | |
6 A (at 24 V, AC15) | |
6 A (at 120 V, AC15) | |
6 A (at 250 V, AC15) |
Operating mode | 100% operating factor |
---|---|
Degree of protection | RT II (Relay) |
Mechanical service life | 3 x 107cycles |
Flammability rating according to UL 94 | V0 |
Designation | Standards/regulations |
Standards/regulations | IEC 60664 |
EN 50178 | |
IEC 62103 | |
Rated surge voltage/insulation | 6 kV / Safe isolation, increased insulation |
Pollution degree | 2 |
Overvoltage category | III |
Mounting position | any |
Assembly instructions | In rows with zero spacing |
Connection name | Coil side |
---|---|
Connection method | Push-in connection |
Stripping length | 8 mm |
Conductor cross section solid | 0.14 mm² ... 2.5 mm² |
Conductor cross section flexible | 0.14 mm² ... 2.5 mm² |
Conductor cross section AWG | 26 ... 14 |
Título: | Tamanho: | Tipo: |
---|---|---|
PDF CATALOG PHOENIX INTERFACE TECHNOLOGY AND SWITCHING DEVICES EN.pdf | 27 Mbytes | |
PHOENIX CONTACT-2900295-PLC-RPT- 60DC/21HC | 161 Kbytes |
Não há comentários do produto ainda.
Avaliação: | |
Nome: | |
Email: | |
Título: | |
Opinión: | |
Você recomendaria esse produto para comprar? | |
Adicionar avaliação |
Todas as classificações que recebemos a partir dos itens que oferecemos são reais e verificadas. Um pequeno gesto, mas muito valioso. Então, obrigado por esse minuto você gasta em deixar-nos a sua opinião e classificação de produtos, porque nos ajuda a continuar a melhorar e oferecer maior qualidade de serviço.