Standards
EN 61000-6-2
EN 61000-6-4
EN 61131-2
Potential isolation
Yes, through optocoupler
Ambient temperatureAmbient temperature, operation
0 - +55 °C
Ambient temperatureStorage, transport [ϑ]
-25 - +85 °C
Relative humidityRelative humidity
5 - 95 % (indoor), Level RH-2, no condensation (for storage at 45°C)
Ambient conditions, mechanicalDegree of Protection
IP20
Ambient conditions, mechanicalHarmful gases
SO2: 10 (rel. humidity < 75%, no condensation)
H2S: 1.0 (rel. humidity < 75 %,no condensation) ppm
Vibration resistance, operating conditions
according to IEC/EN 60068-2-6
Mechanical shock resistance
according to IEC 60068-2-27 g
Continuous shock resistance (IEC/EN 60068-2-29)
According to IEC 60068-2-29
Drop and topple
According to IEC 60068-2-31, free fall according to IEC 60068-2-32
Electromagnetic compatibility (EMC)ESD [Air/contact discharge]
EN 61000-4-2 kV
Electromagnetic compatibility (EMC)Electromagnetic fields [(0.08…1) / (1,4…2) / (2…2,7) GHz ]
EN 61100-4-2 V/m
Electromagnetic compatibility (EMC)Burst
EN 61100-4-4
Electromagnetic compatibility (EMC)Surge
EN 61100-4-5
Electromagnetic compatibility (EMC)Radiated RFI
EN 61100-4-6 V
Electromagnetic compatibility (EMC)Emitted interference (radiated, high frequency) [(30...230 MHz) / (230...1000 MHz)]
EN 55016-2-3 dB
Electromagnetic compatibility (EMC)Voltage fluctuations/voltage dips
EN 61131-2
Electromagnetic compatibility (EMC)Type test
to EN 61131-2
Other technical data (sheet catalogue)
Rated data
according to VDE 0611 Part 1/8.92 /
IEC/EN 60947-7-1
Connection design in TOP direction
Push-In spring-cage terminals
Clamping range
max. 0.14 - 1.5 mm2
Connectable conductorsOutputs to EN 61131-2
0.25 - 1.5 mm2
Connectable conductorsReset after short-circuit rectified
0.25 - 1.5 mm2
Connectable conductorsVibration resistance, operating conditions
0.25 - 1.5 mm2
Connectable conductors"f" with ferrules with plastic collar according to DIN 46228-1 (ferrules crimped gas-tight)
0.25 - 0.75 mm2
Connectable conductors"e" solid H07V-U
0.25 - 1.5 mm2
Connectable conductors"f" flexible H 07V-K
0.25 - 1.5 mm2
Connectable conductors"f" with ferrules without plastic collar according to DIN 46228-1 (ferrules crimped gas-tight)
0.25 - 1.5 mm2
Connectable conductors"f" with ferrules with plastic collar according to DIN 46228-1 (ferrules crimped gas-tight)
0.25 - 0.75 mm2
Gauge pin IEC/EN 60947-1
A1
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from supply terminal [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Connectable sensors
Resistive loads
Inductive loads
Lamp loads
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from supply terminal [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Load resistanceResistive load
≧ 48 Ω
Load resistanceInductive load
As per DC13 to IEC 60947-5-1 h
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from the supply terminal (at load current = 0 mA) [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Power loss [P]
Normally 1.5 W
Output voltageHigh level [UH⁄UA]
> UL- 1 V DC
Output currentHigh level (rated value) [IH]
0.5 A
Output currentHigh level (permissible range) [IH]
< 1.0 A
Delay on signal change and resistive loadfrom Low to High level
300 µs
Delay on signal change and resistive loadFrom High to Low signal
300 µs
Utilization factor [%]
100 g
Can be connected
Resistive loads
Inductive loads
Lamp loads
Inductive load
As per DC13 to IEC 60947-5-1 h
Switching frequencyWith resistive load [f]
100 Hz
Switching frequencywith inductive load
As per DC13 to IEC 60947-5-1
Switching frequencySwitching frequency with lamp load [f]
10 Hz
Outputs to EN 61131-2
short-circuit proof
Reset after short-circuit rectified [Ii]
Automatic
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from supply terminal [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from supply terminal [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Power loss [P]
Normally 1.5 W
Can be connected
Resistive loads
Inductive loads
Lamp loads
Utilization factor [g]
100 %
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from supply terminal [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from supply terminal [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Output currentHigh level (permissible range) [IH]
< 1.0 A
Output currentHigh level (rated value) [IH]
0.5 A
Switching frequencySwitching frequency with lamp load [f]
10 Hz
Short-circuit rating
short-circuit proof
Rated voltage through supply terminal [UL]
24 V DC
Rated current consumption from supply terminal [IL]
3 mA
Rated current consumption from module bus [IMB]
≦ 15 mA
Power loss [P]
Normally 1.5 W
The supply terminal (UL) provides power for the module electronics and for the consumers at the outputs. The total current required for each module consists of the sum of all partial currents.
Part of the XI/ON module’s electronics is supplied with module bus voltage (5 V DC), the other part through the supply terminal (UL).
To increase the maximum output current to up to 1 A, two outputs can be connected in parallel.
Note for table header
The rated current from supply terminal data apply at zero load current.
Applies for resistive load: RLO < 1kΩ