5/5 .
— CHE 5/6/26, 10:33 AM
Product:MTZ18-4VM DANFOSS REFRIGERATION Reciproc...

Images are for illustrative purposes only. Please refer to data sheet for details.
Reference: CHARX PS-M2/825DC/1000DC/30KW
Code: 1296467
Manufacturer: PHOENIX CONTACT
Description:
Categories:
Brand new product in its original packaging covered by the warranties and certifications provided by PHOENIX CONTACT
LAST VIEWED
| DC operation | |
| Input voltage range | 300 V DC ... 825 V DC |
| Derating | < 650 V DC ... 300 V DC (46 W/V) |
| Nominal input voltage range | 650 V DC ... 825 V DC |
| Input current | 48 A (650 V DC) |
| 38 A (825 V DC) | |
| Inrush current limitation | < 60 A |
| Insulation resistance | > 10 MΩ |
| Supply system configuration | DC grid (DC±, PE) |
| Efficiency | > 95 % (POut>50%) |
| Output voltage range | 30 V DC ... 1000 V DC |
| Output current range | 0 A ... 100 A |
| Nominal power | 30 kW |
| Power dissipation standby | < 14 W |
| Protection against overvoltage at the output (OVP) | > 1040 V DC |
| Derating | > 55 °C (3.2 A/K) |
| > 55 °C (1 kW/K) | |
| Control deviation | < 0.5 % (Voltage deviation static load change 20% ... 100%) |
| < 1 % (Current deviation Static load change 20 % ... 100 %) | |
| ± 0.2 % (Input voltage change ±20 %) | |
| Switch-on delay | < 8 s |
| Overshoot behavior | ± 3 % (Switch-on procedure) |
| Battery technology | Li-Ion |
| Input | |
| Designation | Input |
| Identification | DC IN: + / - / PE |
| Conductor connection | |
| Connection method | Push-in connection |
| rigid | 1.5 mm² ... 16 mm² |
| 10 mm² (recommended) | |
| flexible | 1.5 mm² ... 16 mm² |
| 10 mm² (recommended) | |
| rigid (AWG) | 15 ... 5 (Cu) |
| 7 (recommended) | |
| Stripping length | 18 mm (rigid/flexible) |
| Output | |
| Designation | Output |
| Identification | DC OUT: + / - |
| Conductor connection | |
| Connection method | T-LOX knee lever connection |
| rigid | 10 mm² ... 50 mm² |
| 25 mm² (recommended) | |
| flexible | 16 mm² ... 50 mm² |
| 25 mm² (recommended) | |
| rigid (AWG) | 8 ... 0 (Cu) |
| 16 (recommended) | |
| Stripping length | 20 mm (10 mm² ... 25 mm² = 18 mm, 35 mm² ... 50 mm² = 20 mm) |
| Interface | CAN bus |
| Number of interfaces | 1 |
| Connection method | 2x RJ45 (pin assignment, CANopen standard) |
| Locking | Locking clip |
| Transmission physics | Twisted-Pair |
| Topology | Line (daisy-chain connection) |
| Transmission speed | 125 kbps |
| Transmission length | max. 20 m |
| Supported protocols | CAN 2.0B |
| Electrical isolation | yes (primary/secondary) |
| no (PE) | |
| Number of power modules as CAN bus devices | max. 48 (within one CHARX control controller) |
| Termination resistor | 120 Ω (Terminating the end device) |
| Electrical isolation between input and output | yes |
| Insulation voltage input/output | 2121 V DC |
| Insulation voltage input, output / housing | 2121 V DC |
| Insulation voltage input, output/signal, communication | 4242 V DC |
| Insulation voltage signal, communication/housing | 707 V DC |
| Product type | DC power module |
| Product family | CHARX power basic |
| MTBF (IEC 61709, SN 29500) | > 300000 h |
| Service life | 40000 h (40 °C) |
| 70000 h (40 °C, fan) | |
| Internal fan | yes |
| Flow direction | from front to back |
| Insulation characteristics | |
| Protection class | I |
| Pollution degree | 2 |
| Item dimensions | |
| Width | 483 mm |
| Height | 134 mm |
| Depth | 550 mm |
| Dimensional drawing | ![]() |
| Rack unit | 3 U |
| Mounting type | 19" rack mounting |
| Housing material | Zn-Al alloy |
| Ambient conditions | |
| Degree of protection | IP20 |
| Ambient temperature (operation) | -40 °C ... 70 °C |
| Ambient temperature (storage/transport) | -40 °C ... 70 °C |
| Overtemperature protection (OTP) | > 75 °C |
| Maximum altitude | ≤ 4000 m (Derating >2000 m: 10% / 1000 m) |
| Permissible humidity (operation) | ≤ 95 % (non-condensing) |
| Noise level | < 60 dB (1 m) |
| Overvoltage category | |
| IEC 60664-1 | II |
| Electric vehicle conductive charging system - Part 1: General requirements | |
| Standard designation | Electric vehicle conductive charging system - Part 1: General requirements |
| Standards/specifications | IEC 61851-1 |
| Electric vehicle conductive charging system – Part 23: DC electric vehicle charging station | |
| Standard designation | Conductive charging systems for electric vehicles – Part 23: DC supply equipment for electric vehicles |
| Standards/specifications | IEC 61851-23 |
| EMC requirements for noise emission | EN 61000-6-3 |
| EMC requirements for noise immunity | EN 61000-6-1 |
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.
5/5 .
— CHE 5/6/26, 10:33 AM
Product:MTZ18-4VM DANFOSS REFRIGERATION Reciproc...
5/5 merci beaucoup
— sotitradim 11/29/25, 11:12 AM
Product:SL20,MNM,IP42,300lm,1H SL2MNM42H1C EATON...
4/5 a,azing to use it
— B rahul 10/4/25, 8:05 AM
Product:661601 LEGRAND URA21LED 70LM 1H IP42 NP
4/5 Amazing to use it
— B rahul 10/4/25, 8:04 AM
Product:661601 LEGRAND URA21LED 70LM 1H IP42 NP