F3S-TGR-N_M/-N_USafety door switches Ordering information RFID non-contact switches RFID Non-contact switches are designed to monitor hinge, sliding or removal guard doors. • Based on RFID technology (code) and hall technology (distance check) • The RFID-design covers two operation models with very high anti-tamperlevel: •M-types(Mastercoded):Any sensor works with any actuator,like traditionalswitches • U-types (Unique coded): Each sensor and actuatoruse a unique code. This is a solution for applications that requires even a higher anti-tamper level • Connect up to 20 switches in series •LED supports easy diagnosis • Compensation of mechanical tolerances • Non-contact – no abrasion – no particles • Operates with all OMRON safety controllers •Suitablefor CIP/SIP processes and high pressure cleaning due IP69K (pre-wired types) • Conforms to safety categoriesup to PLe acc. EN ISO 13849-1 Master coded: Any actuatorwill operatewith any sensor (Power down - power up re-teachneeded if exchange of actuator) Unique coded: Only one actuatorfits to the code of the sensor Elongated sensors TypeCable connection Contact configuration Order code Master coded Unique coded 5 m pre-wired 2NC/1NOF3S-TGR-NLPM-21-05F3S-TGR-NLPU-21-05 10 m pre-wiredF3S-TGR-NLPM-21-10F3S-TGR-NLPU-21-10 M12, 8-pinF3S-TGR-NLPM-21-M1J8 F3S-TGR-NLPU-21-M1J8 Small sensors TypeCable connection Contact configuration Order code Master coded Unique coded 5 m pre-wired 2NC/1NOF3S-TGR-NSPM-21-05F3S-TGR-NSPU-21-05 10 m pre-wiredF3S-TGR-NSPM-21-10F3S-TGR-NSPU-21-10 M12, 8-pinF3S-TGR-NSPM-21-M1J8 F3S-TGR-NSPU-21-M1J8 Specifications Mechanical data Item Serial switchingup to 20 pcs. Indicator LEDLED green - Indication of safety circuit closed Operating distance OFF ON (Sao) 10 mm Close ON OFF (Sar)20 mm Open Actuator approach speedMin.4 mm/s Max. 1,000 mm/s Operating temperature–25 to 80°C Enclosure protection Flying leadIP69K M12 connectorIP67 Material cable Flying leadPVC, Ø 6 mm o.d. M12 connector250mm,PVC, Ø 6 mm o.d. MaterialUL approved Polyester Electrical data ItemF3S-TGR-N_M F3S-TGR-N_U Code Master coded: Every switch same code (Power down - Power upUnique coded: 32 x 166 different codes re-teach needed, if actuator interchanged) Technology RFID (code) and Hall (distance check) Power supply24 VDC±15% Power consumption Max. 0.2 A Switching currentMin. 1 mA, 10 VDC Rated loads NC contacts Max. 0.2 A, 24 VDC NO contactMax. 0.2 A, 24 VDC Output type Electronic output (potential-free optocoupler output) 445 F3S-TGR-N_M/-N_USafety door switches Approved standards EN standards certified by TÜV Rheinland EN 62061 EN ISO 14119 EN ISO13849-1 EN 60204-1 Accessories EN standards certified by TÜV Rheinland EN/IEC 60947-5-3 UL 508,CSA C22.2 BS 5304 EN 1088-1 conformance Order code Cables 8-pin 2m Y92E-M12PURSH8S2M-L 5m Y92E-M12PURSH8S5M-L 10 m Y92E-M12PURSH8S10M-L 25 m Y92E-M12PURSH8S25M-L T-Connector connection cable T-Connector for M12 connector F39-TGR-NT 0.6 m, M12-8pin Y92E-M12FSM12MSPURSH806M-L 2 m, M12-8pinY92E-M12FSM12MSPURSH82M-L 5 m, M12-8pinY92E-M12FSM12MSPURSH85M-L 10 m, M12-8pinY92E-M12FSM12MSPURSH810M-L Actuators (only for master coded types)for F3S-TGR-NLPMF39-TGR-NLPM-A for F3S-TGR-NSPMF39-TGR-NSPM-A Mounting screws Set of Torx safety screws (M4, 4 × 30 mm, 4 × 20 mm, 4 × 10 mm incl. washers and Torx bit) F39-TGR-N-SCREWS Wiring examples (Single head connection) G9SA Single sensor application with G9SA-301 (up to PLe acc. EN ISO 13849-1) +24 VGND Start Magnetic actuator F3S-TGR-N_M F3S-TGR-N_U Sensor red blue A1 A2 T31 G9SA-301 Feed- back- loop KM1 KM2 black white yellow green brown orange Aux. Output T11 T12 T22 T21 T32 KM1 13 1433 34 KM1 KM2 KM2 +UsM GND 446
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.