Selected parameters SYSTEM Photo-Amplifier HOUSING rectangular SENSING RANGE Dependend on sensor CONNECTION Plug and Socket OUTPUT RELAY SPDT MATERIAL Plastic Others SENSING RANGE Up to 50 m HOUSING 80 x 75 x 35 mm MATERIAL NORYL ADDITIONAL Multiplexed
Photoelectrics Amplifier Type S142C.. • µ-Processor controlled • Amplifier relay for photoelectric switches • Automatic or manual emitter power regulation • Multiplex system, master/slave 20 ms cycle • Self-diagnostic functions • Alignment help • Rated operational voltage: 24 VAC/DC, 115 VAC or 230 VAC • Output 8 A/250 VAC SPDT relay • LED indication: Automatic gain, output, level, emitter or receiver fault Product Description Ordering Key S142 C RXM 924 µ-Processor controlled amplifier for one set of pho- toelectric sensors, type MOFTR. Utilisingan11-pin circular plug for easy con- nection. 8 A SPDT relay output. Diag- nostics for sensor test during operation.Alignment help via LED. Level indication for Type Selection dirt accumulation. Manual orautomatic emitterpow- er regulation. Master/Slave system fully multiplexed for highneighbourimmunity. Two emitter codes available for high neighbour immunity between two seperate mas- ter/slave networks. Type Special function Output type R-Relay X-None M-Manuel adj. A-Manuel and automatic adj. Power supply Function Ordering no.Ordering no.Ordering no. Supply: 24 VAC/DC Supply: 115 VAC Supply: 230 VAC Manuel or Automatic adj.1)S142 C RXA 924S142 C RXA 115S142 C RXA 230 Manuel adj.2) S142 C RXM 924 S142 C RXM 115 S142 C RXM 230 1) Amplifier can not be used as replacement in old systems, if used in old systems all amplifiers must be replaced. 2) Amplifier direct replacement for S1423156xxx, only for replacement not for new design. Specifications Rated operational voltage (UB) Pins 2 & 10230 195 to 265 VAC, 45 to 65 Hz 115 98 to 132 VAC, 45 to 65 Hz 924 20.4 to 27.6 VAC/DC Class 2 Rated operational power AC supply 3.3 VA AC/DC supply 1.6 VA / 1.4 W Delay on operate (tV) < 300 mS Outputs Relay Rating (AgCdO)µ (micro gap) Resistive loads AC1 8 A / 250 VAC (2500 VA) DC1 0.2 A / 250 VDC (50 W) or 2 A 25 VDC (50 W) Electrical life (typical) AC1 > 100.000 operations Output function Make or break on DIP-switch RelaySPDT Supply to sensors Emitter Pins 5 & 7 Supply voltage (open loop) 15 V square wave Current < 450 mA, short circuit protected Output resistance 10 Ω Receiver Pins 6 & 8 Supply voltage (open loop) 5 VDC Short-circuit current10 mA Input resistance470 Ω Emitter power Power Settings on DIP switch no 4, 50 % or 100 % range Sensitivity adjustment Manual240º Potentiometer Automatic /Auto LED ON)Potentiometer settings fully counter clockwise Max. sensing distance Maximum range indicated on photoelectric switch data- sheets in 100 % settings Rated insulation voltage (UI)250 VAC Dielectric voltage>2.0 KVAC (rms) (contacts / electronics) Rated impulse withstand volt. 4 kV (1.2/50 µS) (contacts / electronics) (IEC 664) Operating frequency (f) Light / Dark ratio 1:1 Relay output 20 HZ Specifications are subject to change without notice (18.09.2013) 1
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.