Cable guide

6288640

KL80A

-

Trunking clamp for system opening 80, Polyamide, PA

Duct clamp KL80A. Duct clamp for holding cables securely and for fastening the partition in Rapid 80 GK, GS and GA device installation trunking systems as well as in ISS service poles with a 76.5 mm system opening.

2204000

2033 M A2

-

Pressure clip , 2x8 NYM3x1,5, Stainless steel, grade 301, VA, 1.4310

Pressure clip for 16 cables. The metal pressure clip is halogen and fire load-free, and maintains a good mechanical stability even in fires. The pressure clip is also approved as a cable-specific variant for the maintenance of electrical functionality to DIN 4102 Part 12. The spacer 2033 D 15 x 3 G (must be ordered separately) increases the clamping height of pressure clips from 10 to 13 mm. The pressure clips are suitable for fireproof mounting above suspended fire protection ceilings in accordance with DIN 4102.

2204010

2034 M A2

-

Pressure clip , 2x5 NYM3x1,5, Stainless steel, grade 301, VA, 1.4310

Pressure clip for 10 cables. The metal pressure clip is halogen and fire load-free, and maintains a good mechanical stability even in fires. The pressure clip is also approved as a cable-specific variant for the maintenance of electrical functionality to DIN 4102 Part 12. The spacer 2033 D 15 x 3 G (must be ordered separately) increases the clamping height of pressure clips from 10 to 13 mm. The pressure clips are suitable for fireproof mounting above suspended fire protection ceilings in accordance with DIN 4102.

2204541

2033 STD

-

Pressure clip , 2x8 NYM3x1,5, Light grey, 7035, Polyamide, PA

Pressure clip with push-fit anchor. With moulded push-fit plug, 6 mm Ø.For max. 16 cables NYM 3 x 1.5 mm²

2204908

2032 F

-

Pressure clip , 1x8 NYM3x1,5, Stone grey, 7030, Polybutylene terephthalate, PBPT

Cable clamp 2032 F 1x8 NYM3x1.5 stone gray Polybutylene terephthalate, PBT

2204916

2033 F

-

Pressure clip , 2x8 NYM3x1,5, Stone grey, 7030, Polybutylene terephthalate, PBPT

Pressure clip for 16 cables, flame resistant. Flame-resistant version, specially for use in suspended ceilings.Thermoplast. Polyester, stone grey RAL 7030, flame-resistant to VDE 0471/DIN IEC 695 Part 2-1, Test temperature 960 °C, respectively V-O to UL 94, halogen-free.Clamping height: 9 mm, with spacer 13 mm.Fastening hole: 6 mm Ø.2033/F for max. 16 conductors NYM 3 x 1.5 mm²

2204924

2034 F

-

Pressure clip , 2x5 NYM3x1,5, Stone grey, 7030, Polybutylene terephthalate, PBPT

Pressure clip for 10 cables, flame resistant. Flame-resistant version, specially for use in suspended ceilings.Thermoplast. Polyester, stone grey RAL 7030, flame-resistant to VDE 0471/DIN IEC 695 Part 2-1, Test temperature 960 °C, respectively V-O to UL 94, halogen-free.Clamping height: 9 mm, with spacer 13 mm.Fastening hole: 6 mm Ø.2034/F for max. 10 conductors NYM 3 x 1.5 mm²

2204975

2032 SP

-

Pressure clip large packaging, 1x8 NYM3x1,5, Light grey, 7035, Polyamide, PA

Pressure clip for 8 cables. Standard version for general use, e.g. on intermediate ceilings and partition walls.Clamping height 9 mm – with spacer 13 mm.Fastening hole: 6 mm Ø.2032 for max. 8 cables NYM 3 x 1.5 mm²

2204983

2033 SP

-

Pressure clip large packaging, 2x8 NYM3x1,5, Light grey, 7035, Polyamide, PA

2204991

2034 SP

-

Pressure clip large packaging, 2x5 NYM3x1,5, Light grey, 7035, Polyamide, PA

2205017

2032

-

Pressure clip , 1x8 NYM3x1,5, Light grey, 7035, Polyamide, PA

Pressure clip for 8 cables. Standard version for general use, e.g. on intermediate ceilings and partition walls.Clamping height 9 mm – with spacer 13 mm.Fastening hole: 6 mm Ø.2032 for max. 8 cables NYM 3 x 1.5 mm²

2205033

2033

-

Pressure clip , 2x8 NYM3x1,5, Light grey, 7035, Polyamide, PA

Pressure clip for 16 cables. Standard version for general use, e.g. on intermediate ceilings and partition walls.Clamping height 9 mm – with spacer 13 mm.Fastening hole: 6 mm Ø.2033 for max. 16 cables NYM 3 x 1.5 mm²

2205041

2034

-

Pressure clip , 2x5 NYM3x1,5, Light grey, 7035, Polyamide, PA

Pressure clip for 10 cables. Standard version for general use, e.g. on intermediate ceilings and partition walls.Clamping height 9 mm – with spacer 13 mm.Fastening hole: 6 mm Ø.2034 for max. 10 cables NYM 3 x 1.5 mm²

2205400

2031 F 10

-

Grip collecting clamp flame-resistant to 960°C, 10x NYM3x1,5, Stone grey, 7030, Polypropylene, PP

2205404

2031 20

-

Grip collecting clamp , 20x NYM3x1,5, Light grey, 7035, Polypropylene, PP

Grip 20. Cable tidy for general use with fastening holes of Ø 6 mm, suitable for wall and ceiling mounting. The moulded fastening element can be fastened using knock-in anchors or a gas pressure nail gun. The recommended fastening spacing when assigned fully is 250–400 mm. With multifunctional fastening element.Capacity: 2031/ 20 max. 20 cables NYM 3 x 1.5 mm²

2205408

2031 20 SP

-

Grip collecting clamp , 20x NYM3x1,5, Light grey, 7035, Polypropylene, PP

2205412

2031 F 20

-

Grip collecting clamp flame-resistant to 960°C, 20x NYM3x1,5, Stone grey, 7030, Polypropylene, PP

Grip 20 flame-resistant. Cable tidy with moulded fastening element, for mounting up to 20 cables NYM 3 x 1.5 mm2 on walls or ceilings. Fastening with impact anchor or push-fit anchor. Fastening hole: Ø 6 mm. Recommended fastening distance of 250–400 cm when fully assigned, depending on the respective national specifications/norms. Flame resistant to DIN VDE 0471/DIN IEC 695 Part 2-1, test temperature 960 °C.With multifunctional fastening element.Capacity: 2031/ 20 max. 20 cables NYM 3 x 1.5 mm²

2205416

2031 40

-

Grip collecting clamp , 40x NYM3x1,5, Light grey, 7035, Polypropylene, PP

Grip 40. Cable tidy for general use with fastening holes of Ø 6 mm, suitable for wall and ceiling mounting. The moulded fastening element can be fastened using knock-in anchors or a gas pressure nail gun. The recommended fastening spacing when assigned fully is 250–400 mm.With multifunctional fastening element. Capacity: 2031/ 40 max. 40 cables NYM 3 x 1.5 mm²

2205420

2031 40 SP

-

Grip collecting clamp , 40x NYM3x1,5, Light grey, 7035, Polypropylene, PP

Grip 40. Cable tidy for general use with fastening holes of Ø 6 mm, suitable for wall and ceiling mounting. The moulded fastening element can be fastened using knock-in anchors or a gas pressure nail gun. The recommended fastening spacing when assigned fully is 250–400 mm.With multifunctional fastening element. Capacity: 2031/ 40 max. 40 cables NYM 3 x 1.5 mm²

2205423

2031 F 40

-

Grip collecting clamp flame-resistant to 960°C, 40x NYM3x1,5, Stone grey, 7030, Polypropylene, PP

Grip 40 flame-resistant. Cable tidy with moulded fastening element, for mounting up to 40 cables NYM 3 x 1.5 mm2 on wall or ceilings. Fastening with impact anchor or push-fit anchor. Fastening hole: Ø 6 mm. Recommended fastening distance of 250–400 cm when fully assigned, depending on the respective national specifications/norms. Flame resistant to DIN VDE 0471/DIN IEC 695 Part 2-1, test temperature 960 °C.With multifunctional fastening element. Capacity: 2031/ 40 max. 40 cables NYM 3 x 1.5 mm²

2207028

2031 M 15 FS

-

Grip collecting clamp , 15x NYM3x1,5, Strip-galvanised, DIN EN 10147, Steel, St

Grip hug. cable bundles 2031 M 15 FS, 15x NYM3x1.5 Steel, St, galvanized in band, DIN EN 10346

2207036

2031 M 30 FS

-

Grip collecting clamp , 30x NYM3x1,5, Strip-galvanised, DIN EN 10147, Steel, St

Grip collection clamp, metal 30 FS. Metal grouped support for high mechanical stability, even in case of fire. Suitable for safe mounting above fire protection ceilings. Also approved as a cable-specific variant for the maintenance of electrical function to DIN 4102 Part 12. For wall and ceiling mounting. Lock can be opened without tools. Detailed information on the approved routing variants can be found in the appropriate testing documentation.

2207060

2031 M 70 FS

-

Grip collecting clamp , 70x NYM3x1,5, Strip-galvanised, DIN EN 10147, Steel, St

Grip collection clamp, metal 70 FS. Metal grouped support for high mechanical stability, even in case of fire. Suitable for safe mounting above fire protection ceilings. Also approved as a cable-specific variant for the maintenance of electrical function to DIN 4102 Part 12. For wall and ceiling mounting. Lock can be opened without tools. Detailed information on the approved routing variants can be found in the appropriate testing documentation.

053597

-

-

GUIDE ARTICULATED 0.75 M

Articulated guide for cable management. Ring diameter 70m. Length 77cm. Translucent/transparent

053598

-

-

GUIDE ARTICULATED 2COMP 0.75 M

Cable worm - 2 compartments - 0.75 m - white