NPN open-collector outputs, 30 VDC, 50 mA max.(residual voltage: 1 V max. for load current 10 mA max.,2 V max. for load current above 10 mA)
PNP open-collector outputs, 30 VDC, 50 mA max.(residual voltage: 1 V max. for load current 10 mA max., 2 V max. for load current above 10 mA)
Laser OFF input, zero reset input, timing input, reset input, bank input
ON: Short-circuited with 0-V terminal or 1.5 V or less OFF: Open (leakage current: 0.1 mA max.)
ON: Supply voltage short-circuited or supply voltage within 1.5 V OFF: Open (leakage current: 0.1 mA max.)
Smart tuning, scaling, sample hold, peak hold, bottom hold, peak-to-peak hold, self-peak hold, self-bottom hold, average hold, zero reset, On-delay timer, OFF-delay timer, keep/clamp switch, (A-B)calculations, thickness calculation, mutual interference prevention, laser deterioration detection, bank function (4 banks)
Judgement indicators: HIGH (orange), PASS (green), LOW (orange), 11-segment main display (red), 11-segmentsub-display (orange), laser ON (green), zero reset (green), enable (green), menu (green), HIGH threshold (orange), LOW threshold (orange)
Power supply voltage
10 to 30 VDC, including 10% ripple(p-p)
3,000 mW max. with power supply voltage of 30 VDC and power supply current of 100 mA (with Sensor connected)
Operating: 0 to 50°C, Storage: -15 to 70°C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
1,000 VAC, 50/60 Hz for 1 min.
Vibration resistance (destruction)
10 to 150 Hz, 0.7-mm double amplitude, 80 min. each in X,Y,and Z directions
Shock resistance (destruction)
300 m/s2 3 times each in six directions (up/down,left/right,forward/backward)
1.Extension cables cannot be coupled and used together.
2.Beam size: Defined as 1/e2 (13.5%) of the central intensity at the smallest value of diameter for the measurement range (typical value) False detections can occur in the case there is light leakage outside the defined region and the surroundings of the target object have a high reflectance in comparison to the target object.
3.Resolution: indicates the degree of fluctuation (±3σ) of analog output when connected to the ZX2-LDA. (The measured value is given for the center distance for OMRON’s standard target object (diffuse-reflective models: white ceramic object, regular-reflective models: 1/4 λ flat mirror) when the response time of the ZX2-LDA is set to 128 ms.) Indicates the repetition accuracy for when the workpiece is in a state of rest. Not an indication of distance accuracy. Resolution performance may not be satisfied in a strong electromagnetic field.
4.Linearity: indicates the error with respect to the ideal straight line of the displacement output in the case of measuring Omron’ s standard target object. Linearity and measured value may vary depending on target object. F.S. indicates the full scope of the measurement range. (ZX2-LD50 (L): 20mm)
5.Temperature characteristic: Value for the case the space between the sensor head and Omron’s standard target object is secured by an aluminum jig. (Measured at the measurement center distance)
*5 These Sensors are classified as Class 2 laser devices for diffuse-reflective models and Class 1 for regular-reflective models under EN 606825-1 and the regulations of Laser Notice No. 50 for FDA certification. CDRH registration has been completed for diffuse-reflective models and is scheduled for regular-reflective models.
6.In the case of Omron’s standard target object (white ceramic)
7.Configure current output (4 to 20mA) and voltage output (±5 V or 1 to 5 V) by MENU mode.
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.