ZG2 Profile sensor Easy profile measurement – “teach&go” The ZG2 enables precise shape measurement on challenging materials and surfaces. An easy and intuitive user interface enables efficient installation, setup and operation. A built-in LCD monitor indicates the measurement result in real time. • Easy to use – intuitive user interface • Live – built-in LCD monitor for setup and immediate profile display • Versatile – 18 measurement tools • Accurate – 5 μm resolution (3 mm / 631 pixels) • Wide profiles – up to 70 mm Ordering information Sensor heads Optical methodSensing distanceResolution Order code Heigt direction Width directionHight directionWidth direction Diffuse reflective 21048 mm70 mm6 μm111 μmZG2-WDS70 Diffuse reflective 10012 mm22 mm2.5 μm 35 μmZG2-WDS22 Diffuse reflective 503 mm8 mm1 μm13 μmZG2-WDS8T Regular reflective 20.5 mm3 mm0.25 μm5 μmZG2-WDS3VT Note: - For details, refer the ratings and specifications table. - Designate the cable length (0.5 m, 2 m) when ordering. Sensor controllers Power supplyOutput typeOrder code 24 VDC NPN ZG2-WDC11A*1 PNPZG2-WDC41A *1Setup support software for PC is attached Accessories (order separately) Real-time parallel output unit Output typeOrder code Parallel mounting adaptor Order code NPNZG-RPD11 PNPZG-RPD41 For 1 unit ZS-XPM1 For 2 units or more ZS-XPM2 RS-232C cable Connecting deviceOrder code For personal computer connection (2 m)ZS-XRS2 For PLC/PT connection (2 m)ZS-XPT2 Sensor head extension cable NameOrder code 3 m extension cableZG2-XC3CR 8 m extension cableZG2-XC8CR 15 m extension cableZG2-XC15CR 25 m extension cableZG2-XC25CR Digital equalizer (relay device) ZG2-XEQ 0.2 m digital equalizer connection cable ZG2-XC02D Controller link unit ItemOrder code Controller link unit ZS-XCN Memory card Capacity Order code 128 MB F160-N1285 256 MB F160-N2565 393 ZG2 Profile sensor Specifications Sensor heads ItemZG2-WDS70ZG2-WDS22ZG2-WDS8TZG2-WDS3VT Optical systemDiffuse reflectiveDiffuse reflective Regular reflective Diffuse reflective Regular reflective Regular reflective Diffuse reflective Measurement range Height direction210±48 mm (In the high-precision mode) 100±12 mm94±10 mm50±3 mm44±2 mm22.3±0.5 mm10.6±0.4 mm Width direction (typical)70 mm22 mm 8 mm 3 mm ResolutionHeight direction*1 6 μm 2.5 μm 1 μm0.25 μm Width direction 111 μm (70 mm/631 pixels) Linearity (in the height direction)*2±0.1% F.S. 35 μm (22 mm/631 pixels) 13 μm (8 mm/631 pixels) 5 μm (3 mm/631 pixels) Temperature characteristic*30.02% F.S./°C 0.03% F.S./°C 0.08% F.S./°C Light sourceTypeVisible semiconductor laser Wavelength658 nm 650 nm Output 5 mW max. output, 1 mW max. exposure (without using optical instruments)1 mW max. Laser class Class 2M of EN60825-1 / IEC60825-1 Class IIIB of FDA (21CFR 1040.10 and 1040.11) Class 2 of EN60825-1 / IEC60825-1 Class II of FDA (21CFR 1040.10 and 1040.11) Beam shape (at measurement center distance)*4 120 μm × 75 mm (typical)60 μm × 45 mm (typical) 30 μm × 24 mm (typical) 25 μm × 4 mm (typical) LEDSTANDBY: Lights when laser irradiation preparation is complete (indication color: green) LD_ON: Lights when the laser is irradiating (indication color: green) Measurement objectSurface of non-transparent objects Surface of non-transparent/transparent objects Environmental resistance Ambient light intensity Illumination on the photo-receiving face 7,000 lx max.: Incandescent lamp Ambient temperatureOperating: 0 to 50°C, Storage: –15 to 60°C (with no icing or condensation) Ambient humidity Operating and storage: 35% to 85% (with no condensation) Degree of protection IP66 (IEC60529)IP67 (IEC60529) Vibration resistance (destruction) 10 to 150 Hz with 0.35 mm single amplitude for 80 min each in X, Y, and Z directions Shock resistance (destruction)150 m/s², 3 times each in 6 directions (up / down, right / left, forward / backward) MaterialsCase: Aluminum diecast, Front cover: Glass, Cable insulation : Heat-resistive polyvinyl chloride (PVC), Connector: Zinc alloy or brass Cable length0.5 m, 2 m (flexible cable) WeightApprox. 650 gApprox. 500 g Approx. 300 g AccessoriesLaser labels(EN : 2 labels, FDA : 3 labels), Ferrite core (1), Instructionmanual *1Obtained by setting an Omron standard measurement object at the measurement center distance and determing the average height of the beam line. The conditions are given in the table below. However, satisfactory resolution cannot be attained in strong electromagnetic fields.The minimum resolution of the ZG2-WDS8T/WDS3VT is 0.25 ƒÊm, even when the average number of operations is increased. Resolution does not go any lower. ModelCCD Mode Average No. of operationsMeasurement object Regular reflective Diffuse reflective ZG2-WDS70/WDS22/WDS8TStandard mode64 Omron standard white alumina ceramic object ZG2-WDS3VTStandard modeOmron standard mirrored object Omron standard diffuse reflective object *2The tolerance for an ideal straight line obtained by determing the average height of an Omron standard measurement object for the beam line. The CCD high-resolution mode is used. Lin- earity varies depending on the measurement object. ModelMeasurement object Regular reflective Diffuse reflective ZG2-WDS70/WDS22/WDS8TOmron standard white alumina ceramic object ZG2-WDS3VT Omronstandard mirrored objectOmron standard diffuse reflective object *3A value attained by using an aluminum jig to secure the distance between the Sensor head and the measurement object. The CCD standard mode is used. *4Defined as 1/e2 (13.5%) of the center light intensity. This may be influenced when light leakage also exists outside the defined area and the reflectivity of the light around the measurement object is higher than that of the measurement object. 394 ZG2 Profile sensor Sensor controllers Item ZG2-WDC11/WDC11A ZG2-WDC41/WDC41A Input/output typeNPN PNP No. of connectable Sensor Heads1 per Controller No. of connectable Controllers2 Measurement cycle *1 16 ms (high-precision mode), 8 ms (standard mode), 5 ms (high-speed mode) Min. display unit10 nm Display range –999.99999 to 999.99999 Display LCD monitor 1.8-inch TFT color LCD (557x234 pixels) LEDs•Judgment indicators for each task (indication color: orange): T1, T2, T3, T4 •Laser indicator (indication color: green): LD_ON •Zero reset indicator (indication color: green): ZERO •Trigger indicators (indication color: green): TRIG External interface Input/output signal lines Analog outputs Select voltage or current (using the sliding switch on the bottom surface) •Voltage output: 10 to 10 V, output impedance: 40 •Current output: 4 to 20 mA, maximum load resistance: 300 Judgment output (ALL-PASSING/ERROR) Trigger auxiliary output (ENABLE/GATE) NPN open collector 30 VDC, 50 mA max. Residual voltage: 1.2 V max. PNP open collector 50 mA max. Residual voltage: 1.2 V max. Laser stop input (LD-OFF)ON: O V short or 1.5 V max. ON: Power supply voltage short or Zero reset input (ZERO) Measurement trigger input (TRIG) Bank switching input (BANK A, B) OFF: Open (leakagecurrent: 0.1 mA max.) power supply voltage –1.5V max. OFF: Open (leakage current: 0.1 mA max.) Serial I/O USB2.0 1 port, full speed (12 Mbps), MINI-B RS-232C 1 port, 115,200 bps max. Parall output*2 Output 18 - terminal Main functionsNo. of settings banks 16 Sensitivity adjustment Multi, High-speedmulti, Auto, Fixed Measurement items Height, 2-point Step, 3-point Step, Edge position, Edge width, Angle, Intersection coordinates,Intersection angle, Sectional area (up to eight items can be measured simultaneously) Auxiliary functions Filter, Laser power adjustment, Position correction (height, position, lope), Linked operation,Point of inflection measurement Profiles saved 16 profiles (1 profile per bank) Trigger modesExternal trigger/continuous Ratings Power supply voltage21.6 to 26.4VDC (including ripple current) Current consumption 0.8 A max. (per sensor head) Insulation resistance20 M at 250V between lead wires and Controller case Dielectric strength1,000 VAC, 50 / 60 Hz for 1 min between lead wires and Controller case Environmental resistance Ambient temperature Operating: 0 to 50°C, Storage:–15 to 60°C (with no icing or condensation) Ambient humidity Operating and storage: 35% to 85% (with no condensation) Degree of protectionIP20(IEC 60529) Vibration resistance (destruction) Vibration frequency: 10 to 150 Hz, single amplitude: 0.35 mm, acceleration: 50 m/s² Shock resistance (destruction) 150 m/s², 3 times each in 6 directions (up/down, right/left, forward/backward) Material Case: Polycarbonate (PC), Cable insulation : Heat-resistive polyvinyl chloride (PCV) Cable length 2 m Weight Approx. 300 g (including cable) (Packed state: Approx. 450 g) Accessories ZG2-WDC_1: Large Ferrite Core (1 piece), Instruction Manual ZG2-WDC_1A: Large Ferrite Core (1 piece), Small Ferrite Core (2 pieces), Instruction Manual, Setup Support Software (CD-ROM), USB cable (1 m) *1The image input periods listed here are for fixed/auto sensitivity. The image input period will be longer for multi-sensitivity, high-speed multi-sensitivity, or other settings. When the high- power mode is ON, the shortest image input period is 95 ms regardless of the setting of the CCD mode. Use the eco monitor in the RUN mode to determine the actual image input period. *2when ZG-RPD is mounted 395 ZG2 Profile sensor Data storage unit Item ZG2-DSU11 ZG2-DSU41 Input/output typeNPN PNP No. of connectable Controllers 2*1 Connectable controllersZG2-WDC11/WDC41 External interface Input/output signal lines Inputting starting/ terminating logging Judgment output (HIGH/PASS/LOW/ERROR) ON:O V short or 1.5 V max. OFF: Open (ileakage current : 0.1 mA max.) NPN open collector 30 VDC, 50 mA max. Residual voltage : 1.2 V max. ON:Power supply voltage short or power supply voltage –1.5V max. OFF:Open (leakage current: 0.1 mA max.) PNP open collector 50 mA max. Residual voltage: 1.2 V max. Serial I/O USB2.0 1 port, full speed (12 Mbps), MINI-B RS-232C 1 port, 115,200 bps max. FunctionsNo. of logged Memory of the main unit Profiles saved: 5,120 profiles data*2 Memory card (256 MB)*4 Measurement values saved: 65,000 values max.*3 Profiles saved: 35,328 profiles max. (256 profiles x 138 files) Measurementvalues saved: 7,150,000 values max. (65,000 values x 110 files) Logging trigger functionsExternal triggers, data triggers (self-triggers), and time triggers External banks functions 4096 Other functionsAlarm output functions RatingsPower supply voltage21.6 to 26.4VDC (including ripple current) Current consumption 0.5 A max. Environmental resistance Ambient temperature Operating: 0 to 50°C, Storage:0 to 60°C (with no icing or condensation) Ambient humidity Operating and storage: 35% to 85% (with no condensation) Material Case : Polycarbonate (PC) Cable length 2 m Weight Approx. 280 g Accessories Ferrite Core (1 piece), Instruction Manual *1The controller link unit is necessary for linking. *2Data is saved in the memory of the main unit during logging. The data is automatically saved in a memory card after logging is completed. The maximum number of logging differs according to set conditions. For details, refer to the Users Manual. *3Measurement values for 65,000 measurementscan be saved even when two sensor controllers are connected and each performs eight tasks. *4The value is the maximum number achieved in the following conditions: • One sensor controller performs one measurement task. •Either profiles or measurement values are logged. 396
Todas las valoraciones que recibimos de los artículos que ofrecemos son reales y están verificadas. Un pequeño gesto, pero de mucho valor. Por eso, te agradecemos ese minuto que inviertes en dejarnos tu opinión y calificación sobre los productos, porque nos ayuda a seguir mejorando y a ofrecerte un servicio de todavía mayor calidad.