Display - Type
Color display, TFT
Resolution
VGA
640 x 480 Pixel
Visible screen area
115 x 86 mm
Number of colours
64 k Colours
Contrast ratio (Normally)
Normally 300:1
Brightness
Normally 250 cd/m2
Back-lighting
LED
dimmable via software
Service life of back-lighting
Normally 40000 h
Resistive touch protective screen
Touch sensor (glass with foil)
Technology
Resistive-Touch
4 wire
Touch sensor
Glass with film
Processor
RISC CPU, 32 Bit, 400 MHz
Internal memory
DRAM (OS, Program and data memory): 64 MByte
NAND-Flash (can be used for data backup): approx. 128 MByte available
NVRAM (retained data): approx. 32 KByte available
External memory
SD Memory Card Slot: SDA Specification 1.00
Cooling
Fanless CPU and system cooling, natural convection-based passive cooling
Back-up of real-time clockBattery (service life)
non-replaceable, CR2032 soldered in
Back-up of real-time clockBackup (time at zero voltage)
Normally 10 years
Visualisation software
GALILEO
EPAM
XSOFT-CODESYS-2
XSOFT-CODESYS-3
PLC-Programming software
XSOFT-CODESYS-2
XSOFT-CODESYS-3
Target and web visualization
Yes
PLC-licence
PLC licence inclusive
Operating system
Windows CE 5.0 (licence incl.)
Interfaces, communication
built-in interfaces
1 x Ethernet 10/100 Mbps
1 x RS485
1 x USB host 2.0
1 x USB device
1 x PROFIBUS/MPI
1 x SmartWire-DT
USB Host
USB 2.0 (1.5 - 12 Mbit/s), not galvanically isolated
USB device
USB 2.0, not galvanically isolated
Ethernet
100Base-TX/10Base-T
Nominal voltage
24 V DC SELV (safety extra low voltage)
permissible voltage
Effective: 19.2-30.0 V DC (rated operating voltage -20%/+25%)
Absolute with ripple: 18,0-31,2 V DC
Battery powered: 18,0-31,2 V DC (rated operating voltage -25%/+30%)
35 V DC for a duration of < 100 ms
Voltage dips
≤ 10 ms from rated voltage (24 V DC)
5 ms from undervoltage (19.2 V DC) ms
Power consumption [Pmax.]
10 W
Note on power consumption
Basic device
USB Slave to USB Host: 2.5
Total: 9.5
Note on heat dissipation
Heat dissipation with power consumption for 24 V
7 W for basic device + 2.5 W for USB module
Protection against polarity reversal
yes
Type of fuse
Yes (fuse not accessible)
Potential isolation
no potential isolation
Housing material
Plastic, gray
Front type
Standard front with standard membrane (fully enclosed)
Dimensions (W x H x D)
170 x 130 x 39 mm
flush mounted
Clearance: W x H x D ≥ 30 mm (1.18")
Inclination from vertical: ±45° (if using natural convection)
Degree of protection (IEC/EN 60529, EN50178, VBG 4)
IP65 (at front), IP20 (at rear)
ApprovalsApprovals
cUL (UL508)
EAC
ApprovalsExplosion protection (according to ATEX 94/9/EC)
II 3D Ex II T70°C IP5x: Zone 22, Category 3D
Approvalsshipping classification
DNV GL
Applied standards and directivesEMC
(in relation to CE)
EN 61000-6-2
EN 61000-6-4
EN 61131-2
Applied standards and directivesExplosion protection (relevant for CE)
EN 60079-0
EN 61241-1
EN 13463_x
Applied standards and directivesProduct standards
EN 50178
EN 61131-2
Applied standards and directivesSecurity
EN 60950
UL 60950
Mechanical shock resistance
according to IEC 60068-2-27 g
Vibration
according to IEC/EN 60068-2-6
Climatic environmental conditionsAir pressure (operation)
795 - 1080 hPa
TemperatureStorage / Transport [ϑ]
-20 - +60 °C
TemperatureOperating ambient temperature min.
0 °C
TemperatureOperating ambient temperature max.
+50 °C
Relative humidityRelative humidity
10 - 95%, non-condensing
Rated operational voltage [UAux]
24 V DC (-20/+25%) V
Residual ripple on the input voltage
≦ 5 %
Protection against polarity reversal
Yes
Note
If contactors with a total power consumption > 3 A are connected, a power feeder module EU5C-SWD-PF1/2 has to be used.
Short-circuit rating
no, external fuse FAZ Z3
Rated operating voltage of 24-V-DC slaves
typ. UAux- 0.2 V
Supply voltage [UPow]
24 DC -20 % + 25 % V
Input voltage ripple
≦ 5 %
Protection against polarity reversal
yes
Inrush current and duration
12.5 A/6 ms A
Heat dissipation at 24 V DC
1.0 W
Potential isolation between UPowand 15 V SmartWire-DT supply voltage
No
Bridging voltage dips
10 ms
SmartWire-DT supply voltage
Rated operating voltage [Ue]
14,5 ± 3 % V
Note
If SmartWire-DT modules with a total power consumption > 0.7 A are connected, a power feeder module EU5C-SWD-PF2 has to be used.
Connection supply voltages
Connection type
Push in terminals
Flexible with ferrule
0.25 - 1.5 mm2
UL/CSA solid or stranded
24 - 16 AWG
Station type
SmartWire-DT master
Number of SmartWire-DT slaves
99
Address allocation
automatic
Status indication
SmartWire-DT master LED: red/green
Configurations LED: red/green
Plug connector
Blade terminal SWD4-8MF2