Selected parameters SYSTEM DIN-rail Mount CURRENT RATING CATEGORY 26 - 50 AAC RATED VOLTAGE 600 VAC OUTPUT SWITCHING MODE Full cycle control NUMBER OF POLES 3 CONTROL DC - ANALOGUE POWER CONNECTION Box Clamp MODEL Proportional Controllers Others CURRENT RATING 30AAC @ 40°C (104°F) integrated heatsink CONTROL INPUT 0...10VDC, 0...5VDC, 1...5VDC, potentiometer PRODUCT WIDTH 70mm
Solid State Relays 3-Phasewith IntegratedHeatsink Proportional Switching Controllers TypesRGC2P,RGC3P • 2-pole and 3-pole analog switching solid state contactors • Rated operational voltage: up to 660VAC • Rated operational current: up to 75AAC • Control inputs: 0-20mA, 4-20mA, 12-20mA, 0-5V, 1-5V, 0-10V • Local setting through external potentiometer • Switching modes: phase angle or distributed full cycles (1, 4 or 16 full cycles) • Soft start feature with selectable ramp time up to 5 seconds • Integrated varistor protection on output • Monitoring for SSR and load malfunction • EMR output for alarm indication • 100kA short circuit current rating according to UL508 • DIN or panel mount Product DescriptionOrdering Key RGC 3 P 60 V 65 C1D F M This series gives the possibility to control output power of 3- phase loads with an analog control input. The RGC2P is a 2- phase switching product whilst the RGC3P switches all 3 phases. Input types cover a wide range of current and voltage ranges. Local setting by an external potentiometer isalsopossible. Switching modes cover phase anglecontrol,distributedfull cycle control and soft start for limiting inrushcurrent ofloads having a high temperature coefficient, such as short wave infrared heaters. Detection of mains loss, load loss, SSR short circuit and over- temperature is integrated in some models. Alarm condition is signalled through an EMR output and is visually indicated by the alarm LED. Additional LEDs indicate input and load status. Solid state relay Number of switched poles Type of switching Rated operational voltage Control input Rated operational current Switching mode External supply Integrated fan Monitoring features Specifications are at a surrounding temperature of 25°C unless otherwise specified. Ordering Key(Referto page 4 for valid part numbers) SSR with heatsink Type of switching Rated voltage (Ue), Blocking voltage Control input1 Rated current/ pole @40°C2 Switching mode External supply (Us) Features RGC2: 2-pole switching + 1-pole direct P: Proportional60: 180 - 660VAC, 1200Vp AA: 4-20mADC I: 0-20mADC 4-20mADC 12-20mADC V: 0-5VDC 1-5VDC 0-10VDC 15: 15AAC 25: 25AAC 40: 40AAC 75: 75AAC C1: 1 FC ON, 1FC OFF @ 50% input C4: 4 FC ON, 4FC OFF @ 50% input D: 24VAC/DC A: 90 - 250VAC F: Integrated fan M: Monitoring for Mains loss, Load loss, SSR short circuit, open circuit and OTP with EMR alarm output RGC3: 3-pole switching FC = Full Cycle P: Proportional60: 180 - 660VAC, 1200Vp AA: 4-20mADC I: 0-20mADC 4-20mADC 12-20mADC V: 0-5VDC 1-5VDC 0-10VDC 20: 20AAC 30: 30AAC 65: 65AAC E: Phase Angle C1: 1 FC ON, 1FC OFF @ 50% input C4: 4 FC ON, 4FC OFF @ 50% input C16: 16 FC ON, 16FC OFF @ 50% input S: Soft Start D: 24VAC/DC A: 90 - 250VAC P: Integrated over temperature protection (OTP), mains loss with EMR alarm output F: Integrated fan M: Monitoring for Mains loss, Load loss, SSR short circuit, open circuit and OTP = Over Temperature Protection EMR = Electromechanical Relay 1. Input types I and V require an external supply Us 2. Refer to Derating Curves S16: Soft Start + mode C16 OTP with EMR alarm output Specifications are subject to change without notice (26.05.2015) 1
All ratings we receive from the items we offer are real and verified. A small gesture, but a lot of value. That's why we thank you for that minute you invest in leaving us your opinion and qualification about the products, because it helps us to continue improving and to offer you a service of even higher quality.