Produto adicionado com sucesso ao seu carrinho de compras
ZX-TDS10T
197353
ZXTDS10T
OMRON
1
Disponível Envio hoje
Sensor de contato Padrão 0,4 microns 10mm
Sensor de contacto Standard 0,4 microns 10mm
Sensores Avançados > ZX
* Produto novo em sua embalagem original com todas as garantias e certificações de OMRON
Obrigado pelo seu interesse nos nossos artigos, esperamos que o prazo indicado seja conveniente para si.
Durante a preparação do pedido pode seleccionar o tipo de envío que melhor se adapte ás suas necessidades: Aéreo Express 24Hrs, Terrestre Standard 48/72Hrs, etc.
Note: The resolution refers to the minimum value that can be read when a ZX-TDA_1 amplifier unit is connected.
ZX-SW11EV31 |
*Robot cable models are also available. The model numbers are ZX-XC_R.
Measuring ordinary flat surfaces (standard | |||||
Mounting D5SN-TN1/-TF1 or commercially |
Note:Replacement possibleConversion adapter required
Possible average count settings3 | ||
Linear output4 | Current output: 4 to 20 mA/F.S., max. load resistance: 300 Ω Voltage output: ±4 V (±5 V, 1 to 5 V5), output impedance: 100 Ω | |
NPN open-collector outputs, 30 VDC, 30 mA max. | PNP open-collector outputs, 30 VDC, 30 mA max. | |
Zero reset input, timing input, reset input, judgement output hold input | ON: Supply voltage short-circuited or supply voltage of 1.5 V or less | |
| ||
Judgement indicators: High (orange), pass (green), low (yellow), 7-segment main digital display (red), 7-segment sub-digital | ||
140 mA max. (with sensor connected), for 24-VDC power supply voltage: 140 mA max. (with sensor connected) | ||
Operating and storage: 0 to 50°C (with no icing or condensation) | ||
Case: PBT (polybutylene terephthalate), cover: Polycarbonate |
Resolution7 | ||||
Linearity8 | ||||
Operating force9 | ||||
Operating: 0 to 50°C, storage:-15 to 60°C (with no icing or condensation) | ||||
Operating and storage: 35% to 85% (with no icing or condensation) | ||||
Temperature characteristic10 | ||||
Instruction manual, preamplifier mounting brackets (ZX-XBT1) |
1.When using the ZX-TDA11/41 with the SmartMonitor, either the ZX-SFW11EV3 or the
ZX-SW11EV3 SmartMonitor must be used. Earlier versions cannot be used.
3.The response speed of the linear output is calculated as the measurement period x (average count setting + 1).
The response speed of the judgement outputs is calculated as the measurement period x (average count setting + 1).
4.The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.
7.The resolution is given as the minimum value that can be read when a ZX-TDA_1 amplifier unit is connected. This value is taken 15 minutes after turning ON the power with the average number of operations set to 256.
9.These figures are representative values that apply for the measurement mid-point, and are for when the provided actuator is used, with the actuator moving downwards. If the actuator moves horizontally or upwards, the operating force will be reduced. Also, if an actuator other than the standard one is used, the operating force will vary with the weight of the actuator itself.
Título: | Tamanho: | Tipo: |
---|---|---|
ZX-TDS10T ZXTDS10T 197353 measurement_sensors_brochure_en.pdf | 1 Mbytes | |
ZX-TDS10T ZXTDS10T 197353 zx_t_series_brochure_en.pdf | 606 Kbytes |
Não há comentários do produto ainda.
Avaliação: | |
Nome: | |
Email: | |
Título: | |
Opinión: | |
Você recomendaria esse produto para comprar? | |
Adicionar avaliação |
Todas as classificações que recebemos a partir dos itens que oferecemos são reais e verificadas. Um pequeno gesto, mas muito valioso. Então, obrigado por esse minuto você gasta em deixar-nos a sua opinião e classificação de produtos, porque nos ajuda a continuar a melhorar e oferecer maior qualidade de serviço.