BDF-WLS3 CARLO GAVAZZI Parametri selezionati Altro INFO1 controllore remoto INFO2 55 x 45 x 12 INFO3 Battery..

Remote Control
BDF-WLS3
smart-house transmitter for building automation applications
3 individually programmable push-buttons
3 V battery supply (CR2032)
Channel programming using BGP-COD-BAT Range up to 40 m in open air
Battery life: up to 5 years at normal use
INPUT SPECIFICATIONS
Wireless push-button
Transmission frequency 868 MHz
SUPPLY SPECIFICATIONS
Power supply Battery: CR2032 3V
GENERAL SPECIFICATIONS
Channel coding Via BGP-COD-BAT and special cable: GAP-TPH-CAB.
Following the installation, the program- ming can be changed by removing the thin cover between the push-buttons and using the supplied adapter for the GAP-TPH-CAB cable.
Battery change It is possible to change battery if the
battery voltage is low. Use a sharp object to separate the two plastic parts. Replace the battery and reassemble the plastic parts by pressing them together.
Out 1-3 Push-button 1-3
Housing Compact
Environment
Protection degree IP 20
Pollution degree 3 (IEC 60664) Operating temperature 0-50°C/32-122°F Storage temperature -20-70°C/-4-158°F
Humidity
(non-condensing) 20 - 80%
Weight 30 g – battery included
MODE OF OPERATION
The BDF-WLS3 remote control is designed for base unit BH4-WBUx-
230 and will only function with this unit.
The remote control is programmed using a BGP-COD-BAT (see data sheet for this unit).
The communication between BDF- WLS3 and the BH4-WBUx-230 base is established in the following way:
- Push the “Mode” button on the BH4-WBUx-230 base until the red LED indicates association.
- Push the push-button on the BDF- WLS3 remote control module that you want to associate with the BH4-WBUx-230 base.
Once the association is complete, the LED will light up briefly (approx. 1 second).
If the association fails, e.g. because the range is exceeded, the LED in the remote control module will light up simultaneously for approx.
500 ms. This also occurs if, under normal circumstances, it is not possible to establish connection
between the BH4-WBUx-230 base and the BDF-WLS3 remote control modules.
It is possible to disable the commu- nication between the BH4-WBUx-
230 base and all the modules with which it is associated.
- Push the “Mode” button on the BH4-WBUx-230 base until the red “Disable” LED is lit.
This means that there is no connec- tion between the BH4-WBUx-230 base and its associations.
To reestablish the connection, push
“Mode” until neither “Associate” or
“Deactivate” are lit.
Under normal circumstances, the
“Supply” and “smart-house” LEDs
will be lit continuously, whereas
the LED for “Communication” only
blinks briefly when you push an
associated BDF-WLS3 remote con-
trol.
The LED always lights up when you
push a button.
The LED indication provides confir-
mation that the communication is
successful.
DIMENSIONS (mm)
12
45
TYPE SELECTION
Supply Ordering no
Battery BDF-WLS3
2 3 COMMUNICATION EXAMPLE
1
smart-house bus
2 3
1
PUSH BOTTON/LED ALLOCATION
1 2 BH8-CTRLZx-xxx
1 2 BH4-WBUA-230
2 3
1
LED
IO1 Pushbutton 1
IO2 Pushbutton 2
IO3 Pushbutton 3
IO5 LED IO6 LED IO7 LED
Power
smart-house
RF Associate Disable
Mode
Specifications are subject to change without notice (07.11.2007) - A product of the CARLO GAVAZZI Group