Digital I/O device for INTERBUS; fiber optic technology with 500 kbaud, eight inputs (24 V DC), eight outputs (24 V DC, 0.5 A), sensor/actuator connection via 5-pos. M12 female connectors, rugged metal housing, IP67 protection
INTERBUS Ruggedline modules are provided for harsh ambient conditions or in the case of high requirements regarding system diagnostics. To ensure maximum availability, these modules are equipped with a zinc die-cast housing (IP67). Therefore, they can be installed in the direct vicinity of welding tongs.
Each Ruggedline module consists of a mounting plate and and electronics module. The electronics module is snapped onto the mounting plate and fixed with two screws if necessary.
I/O errors can be clearly localized by means of extended diagnostics. Short-circuits of the power supply of the sensors, for example, are reported in groups of 4 inputs. And, in the case of a short-circuit at an output, the respective output is even reported directly. This information will be made available to the controller and displayed at the module.
In the case of modules with fiber optic connection, the diagnostics capability even goes one step further. By using the latest fiber optic technology, the quality of the transmission path is permanently ascertained and optimally adjusted. This information is available to the controller and at the module. Due to these additional features, slow deterioration of the transmission path can be detected before errors occur during transmission or transmission is interrupted.
In the case of Ruggedline modules, the bus medium can be selected. Apart from versions with fiber optic connection (polymer fiber), there are modules which are used with twisted pair cables. The bus medium can be changed from FO installation to a copper medium at any time using the corresponding plug-in adapters.
The bus is connected by means of IP67 plug-in plugs, which transport both the bus signal and the power supply to the modules. For easy preparation, the power supply cable is connected to the plug using the QUICKON fast connection method, and connection of the fiber optic cable is made using a simple cutting and assembly tool; additional polishing is not necessary.
If a fiber optic bus cable is assembled by the user, e.g. the bridge between 2 modules, it must be at least one meter long. For shorter cable bridges, please use only cable bridges from Phoenix Contact.
Note on dimensions
With bus connectors and mounting plate
Ambient temperature (operation)
-20 °C ... 55 °C
Ambient temperature (storage/transport)
-25 °C ... 70 °C
Permissible humidity (operation)
Permissible humidity (storage/transport)
95 % (non-condensing)
Air pressure (operation)
860 hPa ... 1080 hPa (up to 1500 m above mean sea level)
Air pressure (storage/transport)
660 hPa ... 1080 hPa (up to 3500 m above mean sea level)
Degree of protection
Note on weight specifications
Without plug or mounting plate
Seal unused slots/connections to ensure the degree of protection.
Optic fiber (polymer fiber 980/1000 µm)
Power supply for module electronics
24 V DC
Supply voltage range
18.5 V DC ... 32 V DC (including ripple)
Max 3.6 VSS within the permissible voltage range
typ. 120 mA (plus sensor current)
typ. 120 mA (plus sensor current)
2, 3, 4-wire
Number of inputs
Electronic short-circuit/overload protection for each group
Input voltage range "0" signal
-30 V DC ... 5 V DC
Input voltage range "1" signal
11 V DC ... 30 V DC
Typical input current per channel
Delay at signal change from 0 to 1
Delay at signal change from 1 to 0
Number of outputs
Electronic short-circuit/overload protection for each channel
Nominal output voltage
Maximum output current per channel
Maximum output current per group
Nominal load, inductive
12 VA (1.2 H; 48 Ω)
Nominal load, lamp
Nominal load, ohmic
PDF of Digital I/O device for INTERBUS fiber optic technology wi - PHOENIX CONTACT - IBS RL 24 DIO 8/8/8-R-LK - 2734167