160W Dual Output Medical Type RPD-160series
160W Dual Output Medical Type RPD-160series
160W Dual Output Medical Type RPD-160seriesFeatures :
Features :
Features :
Universal AC input / Full range
Universal AC input / Full range
Universal AC input / Full range
Built-in active PFC function
Built-in active PFC function
Built-in active PFC function
Protections: short circuit / Overload/ Over voltage / Over temperature
Protections: short circuit / Overload/ Over voltage / Over temperature
Protections: short circuit / Overload/ Over voltage / Over temperature
5"x3" compactsize
5"x3" compactsize
5"x3" compactsize
Air free convectionfor 100W and 150W with 20.5 CFM forced air
Air free convectionfor 100W and 150W with 20.5 CFM forced air
Air free convectionfor 100W and 150W with 20.5 CFM forced air
Medical safety approved(2 x MOPP betweenprimaryto secondary)
Medical safety approved(2 x MOPP betweenprimaryto secondary)
Medical safety approved(2 x MOPP betweenprimaryto secondary)
With power good and fail signal output
With power good and fail signal output
With power good and fail signal output
No load power consumption under 0.75 W by PS-ON control (G model)
No load power consumption under 0.75 W by PS-ON control (G model)
No load power consumption under 0.75 W by PS-ON control (G model)
Expected
[email protected] with fan, @0.6 A without fan (G model)
Expected
[email protected] with fan, @0.6 A without fan (G model)
Expected
[email protected] with fan, @0.6 A without fan (G model)
Suitable for BF application with appropriate system consideration
Suitable for BF application with appropriate system consideration
Suitable for BF application with appropriate system consideration
3 years warranty
3 years warranty
3 years warranty
G: With 5Vsb & no load power consumption < 0.75 W
G: With 5Vsb & no load power consumption < 0.75 W
G: With 5Vsb & no load power consumption < 0.75 W
RPDG
RPDG
RPDG
160B
160B
160B
Blank: Basic function (without 5Vsb)
Blank: Basic function (without 5Vsb)
Blank: Basic function (without 5Vsb)
SPECIFICATION
SPECIFICATION
SPECIFICATION
MODEL
MODEL
MODEL
OUTPUT NUMBER DC VOLTAGE
OUTPUT NUMBER DC VOLTAGE
OUTPUT NUMBER DC VOLTAGE
RATED CURRENT (20.5 CFM)
RATED CURRENT (20.5 CFM)
RATED CURRENT (20.5 CFM)RPD-160B
RPD-160B
RPD-160B
CH1
CH1
CH1
5V
5V
5V
12A
12A
12ACH2
CH2
CH2
24V
24V
24V
3.6
3.6
3.6
OUTPUT
OUTPUT
OUTPUT
CURRENT RANGE (convection) 1 ~ 6A CURRENT RANGE (20.5 CFM) 1 ~ 12A RATED POWER (convection) Note.7 100.2 W RATED POWER (20.5 CFM) Note.8 150.4 W RIPPLE & NOISE (max.) Note.280mVp-p
CURRENT RANGE (convection) 1 ~ 6A CURRENT RANGE (20.5 CFM) 1 ~ 12A RATED POWER (convection) Note.7 100.2 W RATED POWER (20.5 CFM) Note.8 150.4 W RIPPLE & NOISE (max.) Note.280mVp-p
CURRENT RANGE (convection) 1 ~ 6A CURRENT RANGE (20.5 CFM) 1 ~ 12A RATED POWER (convection) Note.7 100.2 W RATED POWER (20.5 CFM) Note.8 150.4 W RIPPLE & NOISE (max.) Note.280mVp-p
0.2 ~ 2.8
0.2 ~ 2.8
0.2 ~ 2.8
0.2 ~ 3.6
0.2 ~ 3.6
0.2 ~ 3.6
200mVp-p
200mVp-p
200mVp-p
VOLTAGE ADJ. RANGE of
VOLTAGE ADJ. RANGE of
VOLTAGE ADJ. RANGE of
CH1: 5 ~ 5.5 V
CH1: 5 ~ 5.5 V
CH1: 5 ~ 5.5 V
VOLTAGE TOLERANCE Note.3 2.5%
VOLTAGE TOLERANCE Note.3 2.5%
VOLTAGE TOLERANCE Note.3 2.5%
6.0%
6.0%
6.0%
LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.)
LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.)
LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.)
0.5%
0.5%
0.5%
1.5%
1.5%
1.5%
1800ms, 30ms/230VAC3500ms, 30ms/115VAC at full load
1800ms, 30ms/230VAC3500ms, 30ms/115VAC at full load
1800ms, 30ms/230VAC3500ms, 30ms/115VAC at full load
16ms/230VAC/115VAC at full load
16ms/230VAC/115VAC at full load
16ms/230VAC/115VAC at full load
1.0%
1.0%
1.0%
3.0%
3.0%
3.0%
VOLTAGE RANGE Note.6 90 ~ 264VAC 127 ~ 370VDC
VOLTAGE RANGE Note.6 90 ~ 264VAC 127 ~ 370VDC
VOLTAGE RANGE Note.6 90 ~ 264VAC 127 ~ 370VDC
INPUT
INPUT
INPUT
FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.)
FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.)
FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.)
AC CURRENT (Typ.) INRUSH CURRENT (Typ.)
AC CURRENT (Typ.) INRUSH CURRENT (Typ.)
AC CURRENT (Typ.) INRUSH CURRENT (Typ.)
47 ~ 63Hz
47 ~ 63Hz
47 ~ 63Hz
PF>0.93/230VAC PF>0.98/115VAC at full load
PF>0.93/230VAC PF>0.98/115VAC at full load
PF>0.93/230VAC PF>0.98/115VAC at full load
84%
84%
84%
1.7 A/115VAC 0.9 A/230VAC
1.7 A/115VAC 0.9 A/230VAC
1.7 A/115VAC 0.9 A/230VAC
COLD START 35A/115VAC 70A/230VAC
COLD START 35A/115VAC 70A/230VAC
COLD START 35A/115VAC 70A/230VAC
The LEAKAGE CURRENTNote.9 Earth leakage current < 200A/264VAC , Touch current < 100 a/264VAC
The LEAKAGE CURRENTNote.9 Earth leakage current < 200A/264VAC , Touch current < 100 a/264VAC
The LEAKAGE CURRENTNote.9 Earth leakage current < 200A/264VAC , Touch current < 100 a/264VAC
105 ~ 135% rated output power
105 ~ 135% rated output power
105 ~ 135% rated output powerPROTECTION
PROTECTION
PROTECTION
The OVERHEAD of
The OVERHEAD of
OVERLOADOVER VOLTAGE
OVER VOLTAGE
OVER VOLTAGE
THE EXCESS OF TEMPERATURE
THE EXCESS OF TEMPERATURE
THE EXCESS OF TEMPERATURE
5V STANDBY (G model)
5V STANDBY (G model)
5V STANDBY (G model)
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Hiccup mode, recovers automatically after fault condition is removed
CH1: 5.75 ~ 6.75 V
CH1: 5.75 ~ 6.75 V
CH1: 5.75 ~ 6.75 V
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Shut down o/p voltage, re-power on to recover
105(TSW1) detect on heatsink of power transistor
105(TSW1) detect on heatsink of power transistor
105(TSW1) detect on heatsink of power transistor
90(TSW2 ) detect on heatsink of power transistor
90(TSW2 ) detect on heatsink of power transistor
90(TSW2 ) detect on heatsink of power transistor
Protection type : (TSW1)Shut down o/p voltage, recovers automatically after temperature goes down
Protection type : (TSW1)Shut down o/p voltage, recovers automatically after temperature goes down
Protection type : (TSW1)Shut down o/p voltage, recovers automatically after temperature goes down
Protection type : (TSW2)Shut down o/p voltage, re-power on to recover
Protection type : (TSW2)Shut down o/p voltage, re-power on to recover
Protection type : (TSW2)Shut down o/p voltage, re-power on to recover
5VSB :
[email protected] without fan, 0.8 A fan 20.5 CFM ; tolerance2%, ripple : 50mVp-p(max.)
5VSB :
[email protected] without fan, 0.8 A fan 20.5 CFM ; tolerance2%, ripple : 50mVp-p(max.)
5VSB :
[email protected] without fan, 0.8 A fan 20.5 CFM ; tolerance2%, ripple : 50mVp-p(max.)
The FUNCTION
The FUNCTION
The FUNCTION
PS-the INPUT SIGNAL (G model)Power supply: PS-ON = "Hi" or "> 2 ~ 5V" ; power off: PS-ON = "Low" or "< 0 ~ 0.5 V"
PS-the INPUT SIGNAL (G model)Power supply: PS-ON = "Hi" or "> 2 ~ 5V" ; power off: PS-ON = "Low" or "< 0 ~ 0.5 V"
PS-the INPUT SIGNAL (G model)Power supply: PS-ON = "Hi" or "> 2 ~ 5V" ; power off: PS-ON = "Low" or "< 0 ~ 0.5 V"
POWER GOOD / POWER FAIL500ms>PG>10ms PF>1ms
POWER GOOD / POWER FAIL500ms>PG>10ms PF>1ms
POWER GOOD / POWER FAIL500ms>PG>10ms PF>1ms
WORKING TEMP. WORKING HUMIDITY
WORKING TEMP. WORKING HUMIDITY
WORKING TEMP. WORKING HUMIDITY
ENVIRONMENT STORAGE TEMPERATURE, HUMIDITY TEMP. COEFFICIENT VIBRATION
ENVIRONMENT STORAGE TEMPERATURE, HUMIDITY TEMP. COEFFICIENT VIBRATION
ENVIRONMENT STORAGE TEMPERATURE, HUMIDITY TEMP. COEFFICIENT VIBRATION
SAFETY STANDARDS
SAFETY STANDARDS
SAFETY STANDARDS
-20 ~ +70c (Refer to "Reduction Curve")
-20 ~ +70c (Refer to "Reduction Curve")
-20 ~ +70c (Refer to "Reduction Curve")
20 ~ 90% RH non-condensing
20 ~ 90% RH non-condensing
20 ~ 90% RH non-condensing
-40 ~ +85℃, 10 ~ 95% RH
-40 ~ +85℃, 10 ~ 95% RH
-40 ~ +85℃, 10 ~ 95% RH
0.03%/c (0 ~ 50 ° c)
0.03%/c (0 ~ 50 ° c)
0.03%/c (0 ~ 50 ° c)
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, y, Z axes
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, y, Z axes
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, y, Z axes
ANSI/AAMI ES60601-1, TUV EN60601-1 approved
ANSI/AAMI ES60601-1, TUV EN60601-1 approved
ANSI/AAMI ES60601-1, TUV EN60601-1 approved
SECURITY and
SECURITY and
SECURITY and
ISOLATION LEVELPrimary-Secondary: 2xMOPP, Primary-Earth:1xMOPP, Secondary-Earth:1xMOPP
ISOLATION LEVELPrimary-Secondary: 2xMOPP, Primary-Earth:1xMOPP, Secondary-Earth:1xMOPP
ISOLATION LEVELPrimary-Secondary: 2xMOPP, Primary-Earth:1xMOPP, Secondary-Earth:1xMOPP
EMC
EMC
EMC
RESISTANCE TO STRESS
RESISTANCE TO STRESS
RESISTANCE TO STRESS
I/P-O/P:4KVACI/P-FG:2KVAC
I/P-O/P:4KVACI/P-FG:2KVAC
I/P-O/P:4KVACI/P-FG:2KVAC
O/P-FG:1.5 KVAC
O/P-FG:1.5 KVAC
O/P-FG:1.5 KVAC
(Note 4)
(Note 4)
(Note 4)OTHER
OTHER
OTHER
ISOLATION RESISTANCE EMC EMISSION
ISOLATION RESISTANCE EMC EMISSION
ISOLATION RESISTANCE EMC EMISSION
EMC IMMUNITY MTBF
EMC IMMUNITY MTBF
EMC IMMUNITY MTBF
DIMENSION
DIMENSION
DIMENSION
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25c/ 70% RH
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25c/ 70% RH
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25c/ 70% RH
Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3
Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3
Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A
196.3 K hrs min. MIL-HDBK-217F (25c)
196.3 K hrs min. MIL-HDBK-217F (25c)
196.3 K hrs min. MIL-HDBK-217F (25c)
127*76.2*34.6 mm (L*W*H)
127*76.2*34.6 mm (L*W*H)
127*76.2*34.6 mm (L*W*H)
PACKING0.33Kg; 36pcs/12.9 Kg/0.79 CUFT
PACKING0.33Kg; 36pcs/12.9 Kg/0.79 CUFT
PACKING0.33Kg; 36pcs/12.9 Kg/0.79 CUFTNOTE 1. All parameters NOT specially mentioned are measured at 230vac input, ratedload and 25 ° c ambient temperature.
NOTE 1. All parameters NOT specially mentioned are measured at 230vac input, ratedload and 25 ° c ambient temperature.
NOTE 1. All parameters NOT specially mentioned are measured at 230vac input, ratedload and 25 ° c ambient temperature.
2. Curly and noiseare measured at 20 mhz of bandwidth by usinga 12" twistedpair wire terminated with a 0.1 uf & 47uf parallel capacitor.
2. Curly and noiseare measured at 20 mhz of bandwidth by usinga 12" twistedpair wire terminated with a 0.1 uf & 47uf parallel capacitor.
2. Curly and noiseare measured at 20 mhz of bandwidth by usinga 12" twistedpair wire terminated with a 0.1 uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The powersupplyis considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
4. The powersupplyis considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
4. The powersupplyis considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For information on how to perform these EMC tests, please refer to "EMI testingof component powersupplies."
EMC directives. For information on how to perform these EMC tests, please refer to "EMI testingof component powersupplies."
EMC directives. For information on how to perform these EMC tests, please refer to "EMI testingof component powersupplies."
(available in http://www.meanwell.com)
(available in http://www.meanwell.com)
(available in http://www.meanwell.com)
5. HS1,HS2 AND HS3 can not be shorted.
5. HS1,HS2 AND HS3 can not be shorted.
5. HS1,HS2 AND HS3 can not be shorted.
6. The reduction may be necessary underlow input voltages. Please, verify the reduction of the curvefor more information.
6. The reduction may be necessary underlow input voltages. Please, verify the reduction of the curvefor more information.
6. The reduction may be necessary underlow input voltages. Please, verify the reduction of the curvefor more information.
7. The ratedpowerincludes 5Vsb @ 0.6 A.
7. The ratedpowerincludes 5Vsb @ 0.6 A.
7. The ratedpowerincludes 5Vsb @ 0.6 A.
8. The ratedpowerincludes 5Vsb @ 0.8 A.
8. The ratedpowerincludes 5Vsb @ 0.8 A.
8. The ratedpowerincludes 5Vsb @ 0.8 A.
9. Touchcurrentwasmeasured of the main entrance to the DC output.
9. Touchcurrentwasmeasured of the main entrance to the DC output.
9. Touchcurrentwasmeasured of the main entrance to the DC output.File name:RPD-160-SPEC2015-07-17
File name:RPD-160-SPEC2015-07-17
File name:RPD-160-SPEC2015-07-17